Bedienungsanleitung Erbauer EMIS216S (Seite 11 von 37) (Englisch)

779795

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

d) Push the saw through the workpiece. Do not pull the saw through the

workpiece. To make a cut, raise the saw head and pull it out over the

workpiece without cutting, start the motor, press the saw head down and

push the saw through the workpiece. Cutting on the pull stroke is likely to

cause the saw blade to climb on top of the workpiece and violently throw the blade

assembly towards the operator.

e) Never cross your hand over the intended line of cutting either in front or

behind the saw blade. Supporting the workpiece “cross handed” i.e. holding the

workpiece to the right of the saw blade with your left hand or vice versa is very

dangerous.

f) Do not reach behind the fence with either hand closer than 100 mm from

either side of the saw blade, to remove wood scraps, or for any other reason

while the blade is spinning. The proximity of the spinning saw blade to your

hand may not be obvious and you may be seriously injured.

g) Inspect your workpiece before cutting. If the workpiece is bowed or warped,

clamp it with the outside bowed face toward the fence. Always make certain

that there is no gap between the workpiece, fence and table along the line of

the cut. Bent or warped workpieces can twist or shift and may cause binding on

the spinning saw blade while cutting. There should be no nails or foreign objects in

the workpiece.

h) Do not use the saw until the table is clear of all tools, wood scraps, etc.,

except for the workpiece. Small debris or loose pieces of wood or other objects

that contact the revolving blade can be thrown with high speed.

i) Cut only one workpiece at a time. Stacked multiple workpieces cannot be

adequately clamped or braced and may bind on the blade or shift during cutting.

before use.

becoming unstable.

k) Plan your work. Every time you change the bevel or mitre angle setting, make

sure the adjustable fence is set correctly to support the workpiece and will

not interfere with the blade or the guarding system. Without turning the tool

“ON” and with no workpiece on the table, move the saw blade through a complete

simulated cut to assure there will be no interference or danger of cutting the fence.

l) Provide adequate support such as table extensions, saw horses, etc. for

a workpiece that is wider or longer than the table top. Workpieces longer or

wider than the mitre saw table can tip if not securely supported. If the cut-off piece

or workpiece tips, it can lift the lower guard or be thrown by the spinning blade.

m) Do not use another person as a substitute for a table extension or as

additional support. Unstable support for the workpiece can cause the blade

to bind or the workpiece to shift during the cutting operation pulling you and the

helper into the spinning blade.

n) The cut-off piece must not be jammed or pressed by any means against the

spinning saw blade.

wedged against the blade and thrown violently.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Erbauer EMIS216S Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info