Bedienungsanleitung ESQ Aston Chronograph (Seite 1 von 2) (Englisch)

757307

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Operating Instructions

ASTON 1/5 CHRONOGRAPH

A chronograph combines two time-keeping functions. It incorporates

a device to measure intervals of time independent of the regular time

shown on the dial. Your ESQ by Movado Aston Chronograph may be

used to time events up to two hours in duration, in 1/5 of-a-second

increments.

NOTE: After 2 hours of continuous running, the chronograph will stop

and reset automatically to preserve battery life.

Setting the Time:

1. Pull crown out to position 3. (Watch will stop.)

2. Turn crown in either direction to move hands to desired time.

Be sure to take AM/PM into account so that date changes at midnight,

not noon.

3. Push crown back in to position 1. (Watch will restart.)

NOTE: To set time to exact second, pull crown out to position 2 precisely

when small seconds hand S reaches <<60>> position. (Watch stops.)

Adjust time to one minute ahead, and take an accurate time signal, from

a radio news station, for example. When audible tone signals exact time,

immediately push crown back in to position 1. (Watch will restart, now

set to the exact time.)

Setting the Day:

1. Pull crown out to position 3. (Watch will stop.)

2. Turn crown in either direction to move hands forward or back. Each

time the hands complete a 24-hour revolution and pass midnight,

Day indicator hand F will move ahead or back by one day.

3. Once correct Day has been reached, set hands to correct Time,

following instructions above.

4. Push crown back in to position 1. (Watch will restart.)

Setting the Date:

1. Pull crown out to position 2. (Watch will keep running.)

2. Turn crown clockwise to move hands forward. Each time the hands

complete a 24-hour revolution and pass midnight, the date shown in

Date display D will advance by one number.

3. Once correct Date has been reached, push crown back in to position 1.

CAUTION: Never set the date when the hands are between 9:00 PM

and 12:30 AM, while automatic date changing is in progress. Doing so

could damage the calendar mechanism.

Chronograph Function Overview

Use buttons A and B to operate the chronograph. Pressing button A

the first time will start the chronograph. While the chronograph is run-

ning, once the chronograph fifths-of-a-second counter hand C has com-

pleted one turn, minute-counter hand E will jump ahead one minute.

Pressing button A a second time will stop the chronograph. Pressing

button B will reset chronograph hands E and C to zero. Adjusting the

time does not stop the chronograph, but it does block buttons A and B

for as long as the crown is pulled out.

IMPORTANT: Crown must be in position 1 and hands must be at zero

before chronograph is started. Press button B to reset hands to zero.

Do not push button A or B while crown is pulled to position 2 or 3.

If button A or B is accidentally activated while crown is not flush against

case, one or both chronograph hands may become de-synchronized.

Should this occur, see directions for synchronizing hands at end of

following instructions.

Simple chronograph functions:

To measure the duration of a single, non-stop event:

1. Press button A to start chronograph.

2. Press button A a second time to stop chronograph, and read the 2

chronograph hands to determine elapsed time, for example: 14 minutes;

37 and 3/5 of a second.

3. Press button B to reset chronograph to zero.

Accumulated time functions:

To measure the combined time of a series of shorter events, for example

the actual playing time of a football game, where play is repeatedly

interrupted:

1. Press button A to start chronograph.

2. Press button A a second time to stop chronograph.

3. Press button A again to resume measurement.

4. Press button A a fourth time to stop chronograph again.

NOTE: Each time you stop chronograph, chronograph hands will indicate

total accumulated time.

Repeat steps 1 and 2 to add each additional interval of time.

5. After you have taken your final accumulated time reading, press button

B to reset chronograph hands to zero.

Split-time or intermediate time functions:

To take intermediate time readings as a race progresses:

1. Press button A to start chronograph.

2. Press button B to momentarily stop chronograph.

3. Read off the intermediate time, for example:10 minutes, 26 and 2/5

of a second.

Legend

H - Hour hand

M - Minute hand

S - Small seconds hand

F - Day indicator hand

C - Center-mounted chronograph fifths-of-a-second hand

E - Chronograph 30-minutes counter

D - Date display

1, 2, 3 - Crown positions

A - Chronograph start/stop push-button

B - Chronograph split/reset push-button

10 40

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ESQ Aston Chronograph Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info