Bedienungsanleitung ESX se 5800 (Seite 23 von 28) (Deutsch, Englisch)

168695

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

INTERCONNECTION LINE INPUTS

• Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT of the amplifier with appropriate high-value RCA cables.

NOTE: Due to the loudspeakers in bridged mode on channel pair 1/2 and 3/4, the RCA line input must be connected like the following:

1.) Split the stereo RCA output (FL or RL) of the headunit with a Y-connector and connect the jacks

with LINE INPUT CH1 / CH3 of the amplifier

2.) Split the stereo RCA output (FR or RR) of the headunit with a Y-connector and connect the jacks

with LINE INPUT CH2 / CH4 of the amplifier

INTERCONNECTION SPEAKERS

• Connect the front- or rear speakers with the speaker outputs (SPEAKER OUTPUT CH1/2 + BRIDGED - and CH3/4 + BRIDGED -).

• Ensure by any means, that the total impedance load of the bridged speakers is not lower than 4 ohms per channel pair.

Too low impedance cause high temperature and will shut down the amplifier operation.

• Always ensure the correct polarity of the speakers. The interchange of plus and minus cause total loss of bass playback and could

damage the speakers.

INTERCONNECTION SUBWOOFER

• Connect the subwoofer with the speaker outputs (SPEAKER OUTPUT + 5CH -) of the amplifier.

• Ensure by any means, that the total impedance load of of the subwoofer is not lower than 1 ohm. Too low impedance cause high

temperature and will shut down the amplifier operation.

• Always ensure the correct polarity of the speakers. The interchange of plus and minus cause total loss of bass playback and could

damage the speakers.

MODE SWITCH

• Select the 4CH position on the MODE switch in this example. Thereby the input signal on CH1/2 and CH3/4 will be routed to the

subwoofer channel (CH5) and the subwoofer signal will be filtered out.The use of Y-connectors is not required in this case.

CROSSOVER SETTINGS CH1/2 (bridged channel left) and CH3/4 (bridged channel right)

• By using bigger speakers (more than 20cm) you can set the X-OVER switch to the FULL position (Full Range Signal).

• By using smaller speakers (8.7cm - 16cm) you must set the X-OVER switch to the HP Position (Highpass Mode) to avoid any damage

by lower frequencies on the speakers. The cut-off frequency is adjustable with the HPF controller and should be set between

60Hz to 150Hz, depending on the size of the speakers.

LOW PASS CONTROLLER Subwoofer Channel CH5

• The LOW PASS controller adjusts the cut-off point of the frequency range to above. The cut-off frequency is continuously

adjustable from 35 Hz to 250 Hz.

SUBSONICFILTER CONTROLLER Subwoofer Channel CH5

• The SUB SONIC controller (Subsonicfilter) limits the ultralow and not hearable frequencies of the audiosignal to below, to avoid a

mechanical and electrical overloading on the subwoofer. The cut-off frequency is adjustable from 15 to 55 Hz and depends on the size

of the subwoofer.

BASS BOOST CONTROLLER Subwoofer Channel CH5

• The BASS BOOST controller adjusts the bass enhancement between 0db and +12dB.

• A too high bass boost may cause clipping/distortion and damage on the loudspeakers and also may harm your hearing abilities.

Use this controller carefully!

BASS REMOTE CONTROLLER Subwoofer Channel CH5

• The enclosed BASS REMOTE Controller adjusts the subwoofer level e.g. from the driver’s seat.

Please use only the enclosed bass remote controller and cable.

LEVEL CONTROLLER CH1/2 (bridged channel left), CH3/4 (bridged channel right) and CH5

• Turn the LEVEL controller of the amplifier to the 5V position.

• Turn the volume controller of the headunit to 80 - 90% of its full setting.

• Turn the LEVEL controller clockwise until you hear some distortion.

• Then turn back the LEVEL controller slightly until you hear a cleaner sound.

SE5800

INTERCONNECTION EXAMPLE 3-Channel Mode: Stereosystem bridged + Subwoofer

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ESX se 5800 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info