Bedienungsanleitung ESX Q-FOURv2 (Seite 12 von 32) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

700206

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

TROUBLESHOOTING

If you are having problems after installation follow the Troubleshooting procedures below.

Procedure 1:

CheckAmplierforproperconnections.

Verify that POWER LED lights up green. If this is the case, skip to Step 3, if not continue.

1. Check in-line fuse on battery positive cable. Replace if necessary.

2.Checkfuse(s)onamplier.Replaceifnecessary.

3. Verify that Ground connection is connected to clean metal on the vehicle’s chassis. Repair/replace if necessary.

4. Verify that there is enough voltage at the power connection and the REM cable. Verify quality connections for both cables at

amplier,stereo,andbattery/fuseholder.Repair/replaceifnecessary.

Procedure 2:

PROTECT LED lights up red.

1. If the PROTECT lights up red, this is a sign of a possible short in the speaker connections. Check for proper speaker connections

and use an ohm meter to check for possible shorts in the speaker wiring. Too low speaker impedance may also cause PROTECT

 tolight.Thiscanalsobeasignofdrivingtheamplieratveryhighpowergainswithoutadequateairowaroundtheamplier.Shut 

 offthesystemandallowampliertocool.Checkthatthevehiclechargingsystemismaintainingpropervoltage.Ifthepreviousitems

 donotsolvetheproblem,afaultmaybeintheamplier.Inthiscaseyoushouldcontactyourdealer.

Procedure 3:

CheckAmplierforaudiooutput.

1.VerifygoodRCAinputconnectionsatstereoandamplier.Checkentirelengthofcablesforkinks,splices,etc.

Test RCA inputs for AC volts with stereo on. Repair/replace if necessary.

Procedure 4:

CheckAmplierforapoppingnoisewhileturningon.

1.Disconnectinputsignaltoamplierandturnamplieronandoff.

2.Ifthenoiseiseliminated,connecttheremoteleadofampliertosourceunitwithadelayturn-onmodule.

Procedure 5:

CheckAmplierifyouexperienceexcessEngineNoise.

1. Route all signal carrying wires (RCA, speaker cables) away from power and ground wires.

2.Bypassanyandallelectricalcomponentsbetweentheheadunitandtheamplier(s).Connectstereo

 directlytoinputofamplier.Ifnoisegoesawaytheunitbeingbypassedisthecauseofthenoise.

3. Remove existing ground wires for all electrical components. Reground wires to different locations.

Verify that grounding location is clean, shiny metal free of paint, rust etc.

4. Add secondary ground cable from negative battery terminal to the chassis metal or engine block of vehicle.

5. Have alternator and battery load tested by your mechanic. Verify good working order of vehicle electrical system including distributor,

spark plugs, spark plug wires, voltage regulator etc.

2-CHANNEL OPERATION MONO (FIG. 5)

Ifyouwanttoruntheamplierwiththe2lineoutputchannelsfromtheheadunittodrivetwosubwoofers,con-

nect the following setup:

(1) To the head unit, line output left REAR L/CH3 or subwoofer output

(2) To the head unit, line output right REAR R/CH4 or subwoofer output

(3) Subwoofer 1

(4) Subwoofer 2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ESX Q-FOURv2 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info