700330
9
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
9
POWER SUPPLY AND TURN-ON-CONNECTION
INTERCONNECTION
INSTALLATION
The power wiring which is usually installed in on-board car networks is not sufcient for demands of this de-
vice. Make sure that the power wires to GND and to the +12 V terminal has been sufciently specied. A cable
crosssection of at least 10 mm
2
must be used to connect the battery to the terminals of the device.
First connect the GND terminal (Fig. 1, 13) of the device to an appropriate ground connection at the chassis.
To ensure a good connection, residue dirt and dust from the connection point. A loose connection may cause
malfunctions or interferences noise and distortion.
Then connect the +12 V terminal (Fig. 1, 12) of the device with the battery by using an appropriate cable in-
cluding an in-line fuse (Fig. 1, 14). This fuse should be located very close to the battery (Fig. 1, 15); for safety
reasons not more than 30 cm away. Only insert the fuse when the installation, including the connection of the
loudspeakers, has been accomplished.
Then connect the remote turn-on-wire from the head unit (Fig. 1, 11) with the device‘s REMOTE terminal. A
cable with a cross-section of 0.5 mm
2
is adequate.
1. Mount the device in the car as shown below.
2. Avoid any damage or removing of the components of the vehicle like wires, cables, board computer, seat
belts, gastank or the like.
AUDIO SIGNAL CABLES
When installing the audio cables between the RCA outputs of the head unit and the RCA inputs of the device
(Fig. 1, 8), the audio and power supply cables should, if possible, not be routed along the same side of the
vehicle. We recommend a separated installation, e.g. routing the power cable through the cable channel on the
left side and the audio cables through the cable channel on the right side or vice versa. This prevents interfe-
rences due to crosstalk into the audio signal.
PROTECTION CIRCUIT
If the POWER LED (Fig. 1, 1) lits up blue, the device is in normal operation. If the PROTECT LED (Fig. 1, 1)
lits up red, the device is overheated. If this events, the internal built-in protection circuit shuts down the device
automatically. The device should work again properly after cooling down.
4 x 4 x 4 x
9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für ESX Q202A wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info