Bedienungsanleitung ESX QL600.4 (Seite 17 von 24) (Deutsch, Englisch)

700189

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

ENGLISH

FUNCTIONAL INSTRUCTIONS

The CH3/CH4 X-OVER switch selects the desired operating mode of channel 3/4:

FULL: Full-Range mode (the entire frequency range is amplied).

HP: High-Pass mode (frequency is limited downwards, adjustable by the HIGH PASS controller).

LP/BP: Low-Pass/Bandpass mode (frequency is limited upwards, adjustable by the LOW PASS controller). The HIGH PASS

controller then acts as a subsonic lter in this mode and limits the frequency downwards (bandpass function).

NOTE: If this is set higher than the LOW PASS, no sound is heard.

If your head unit does not have a turn-on signal (REM), you can use the automatic turn-on function of the amplier. This works

in two ways, which can be set at the AUTO TURN-ON switch:

DC: This method only works if you use the amplier’s HIGH LEVEL INPUT. The amplier then detects a voltage rise to 6 volts

when the head unit is turned on by a so-called “DC offset” and then turns on the amplier.

VOX: Select this method when using the INPUT RCA jacks. The amplier then detects a voltage increase in the incoming audio

signal when switching on the head unit via the attached RCA cable and then switches on the amplier.

Note: As soon as the head unit is switched off again, the amplier switches itself off.

The terminal for the amplier turn-on (page 15#2, REM IN/OUT) can now be used to supply additional ampliers with a turn-on

signal. Simply connect the REM terminals of the two ampliers and make sure that the other amplier is in “normal” turn-on

mode, which means that the AUTO TURN ON function is disabled.

The REMOTE port is for connecting the cable of the included bass level remote controller. With this, the bass level can be e.g.

be adjusted from the driver’s seat. Only use the supplied bass remote controller and the associated cable. The bass level remote

controller only works in LP/BP mode (Low-Pass/Bandpass) on channel pair 3/4, in COPY mode under CH1/CH2 X-OVER also

on channel pair 1/2.

If your head unit does not have RCA preamp outputs, you can use the amplier’s HIGH LEVEL INPUT as the signal input. To do

this, simply connect the loudspeaker cables of the head unit to the enclosed cable plug as follows:

White: CH1 / left front +

White-Black: CH1 / left front –

Gray: CH2 / right front +

Gray-Black: CH2 / right front –

Green: CH3 / left rear +

Green-Black: CH3 / left rear –

Purple: CH4 / right rear +

Purple-Black: CH4 / right rear –

CH1

–

CH1

CH3

–

CH3

CH2

–

CH2

CH4

–

CH4

The BASS BOOST controller adjusts the bass boost continuously from 0 dB to +12 dB at 40 Hz on channel pair 3/4.

NOTE: Always use this controller with care. A permanently too high bass boost could damage your speakers!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ESX QL600.4 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info