Bedienungsanleitung ESX SXE100.4 (Seite 10 von 32) (Deutsch, Englisch)

700198

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

INPUT SENSITIVITY CH1/2 & CH3/4

Turn the controller LEVEL INPUT (Fig. 1,4 and g. 1,6) of the amplier to the MIN position. Then turn the vol-

ume controller of the head unit to 80 - 90% of its full setting. Now turn LEVEL INPUT clockwise until you hear

some distortion. Then turn back the LEVEL INPUT slightly until you hear a cleaner sound.

VARIABLE HIGH PASS FILTER CH1/2 & CH3/4

If the amplier is to be used for mid-range/tweeter loudspeakers, set the switches X-OVER (Fig. 1,3 and g.

1,9) to HP. Then set the desired cross-over frequency on the HIGH PASS controller (Fig. 1,2 or g. 1,8). Thus

to that only the frequencies above the chosen cross-over frequency will be amplied. This effectively minimizes

distortions and overloads at lower frequencies. A good point to start is at 125 Hz.

If you use big loudspeakers (>20 cm) set X-OVER (Fig. 1,3 and g. 1,9) to FULL. In this case, the HIGH PASS

controllers (Fig. 1,2 or g. 1,8) are without function.

VARIABLE BASS BOOST CH3/4

By using the controller BASS BOOST (Fig. 1,11) you are able to increase the bass enhancement from 0 to 12

dB. ATTENTION: Use the BASS BOOST wisely!

HIGH LEVEL INPUTS & AUTO TURN ON

The high level inputs under HI INPUT (Fig. 5) is suitable to connect the device input with speaker wires, if your

head unit is not equipped with pre-amplier RCA outputs. Extend therefor every regarding speaker cable from

your head unit with appropriate speaker cables from your car audio retailer to the mounting location of the am-

plier. Then connect the each matching loudspeaker cable with the cables of the included High Level Input jack.

CAUTION: Never use the high level inputs and the RCA inputs at the same time. This may damage the

device seriously.

The amplier detects a voltage rise (6 Volts) with a so called ”DC Offset” over the connected input signal on the

high level inputs under HI INPUT (Fig. 5) when the head unit will be switched on. Hence, the amplier will also

be turned on. As soon as the head unit will be turned off, the amplier turns also automatically off. In this case

the turn-on connection REM (Fig. 2,2) is not needed.

NOTE: The Auto Turn On function usually works with 90% of all head units, because they are equipped with

”High Power”-outputs. Only with a few older and head units the Auto Turn On function is not working.

INPUT MODE

By setting the switch INPUT MODE (Fig. 1,7) to the 2CH position, you switch the inputs to a 2-channel mode,

which allows a four-channel operation with only occupying the inputs CH1/2.

VARIABLE LOW PASS FILTER CH3/4

If the amplier is used to drive a subwoofer on CH3/4, set the switch X-OVER (Fig. 1,9) to LP/BP. Set the

desired cross-over frequency by using the controller LOW PASS (Fig. 1,10). Thus to that only the frequencies

below the chosen cross-over frequency will be amplied and the subwoofer plays more precise and efcient.

In LP/BP mode, the controller HIGH PASS (Fig. 1,8) can also be used to limit the frequency response down-

wards, for example to produce a bandpass/subsonic signal. NOTE: If the controller HIGH PASS (Fig. 1,8) is

set higher than the he controller LOW PASS (Fig. 1,10), no audio signal is heard.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ESX SXE100.4 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info