Bedienungsanleitung ESX SXE1200.1D (Seite 11 von 40) (Deutsch, Englisch)

700196

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

INPUT SENSITIVITY

TurntheLEVELINPUT(Fig.1,7)controlleroftheampliertotheMINposition.Thenturnthevolumecontroller

of the head unit to 80 - 90% of its full setting. Now turn LEVEL INPUT clockwise until you hear some distortion.

Then turn back the LEVEL INPUT slightly until you hear a cleaner sound.

VARIABLE BASS BOOST

By using the BASS BOOST controller (Fig. 1,3) you are able to increase the bass enhancement from 0 to 12

dB. ATTENTION: Use the BASS BOOST wisely!

HIGH LEVEL INPUTS & AUTO TURN ON

The high level inputs under HI INPUT (Fig. 6) is suitable to connect the device input with speaker wires, if your

headunitisnotequippedwithpre-amplierRCAoutputs.Extendthereforeveryregardingspeakercablefrom

your head unit with appropriate speaker cables from your car audio retailer to the mounting location of the am-

plier.ThenconnecttheeachmatchingloudspeakercablewiththecablesoftheincludedHighLevelInputjack.

CAUTION: Never use the high level inputs and the RCA inputs at the same time. This may damage the

device seriously.

Theamplierdetectsavoltagerise(6Volts)withasocalled”DCOffset”overtheconnectedinputsignalonthe

highlevelinputsunderHIINPUT(Fig.6)whentheheadunitwillbeswitchedon.Hence,theamplierwillalso

beturnedon.Assoonastheheadunitwillbeturnedoff,theamplierturnsalsoautomaticallyoff.Inthiscase

the turn-on connection REM (Fig. 2,2) is not needed.

NOTE: The Auto Turn On function usually works with 90% of all head units, because they are equipped with

”High Power”-outputs. Only with a few older and head units the Auto Turn On function is not working.

VARIABLE SUBSONIC FILTER

WiththeSUBSONICcontroller(Fig.1,5)youcanadjustthelowercrossoverfrequency,toltertheverylow

frequencies to relieve the subwoofer or to generate a bandpass signal. If you don’t want to use this function,

turn the controller (Fig. 1,5) to the very left to the 10 Hz position.

NOTE: The adjusted value of the SUB SONIC (Fig. 1,5) should not be higher than the adjusted value of the

LOW PASS controller (Fig. 1,4). Otherwise no sound will be audible.

VARIABLE LOW PASS FILTER

Set the desired crossover frequency by using the controller LOW PASS (Fig. 1,4). Thus to that only the fre-

quenciesbelowthechosencrossoverfrequencywillbeampliedandthesubwooferplaysmorepreciselyand

efcient.

BASS LEVEL REMOTE CONTROLLER

With the included bass level cable remote controller you are able to adjust the bass level e.g. out of the driver’s

seat. Connect the remote controller and the REMOTE connector (Fig. 1,2) with the enclosed cable.

PHASE SHIFT CONTROLLER

The PHASE SHIFT controller (Fig. 1,6) allows to adjust the phase between 0° and 180° to match the output

signal with the vehicle’s interior acoustic.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ESX SXE1200.1D Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info