816063
13
Zoom out
Zoom in
Vorherige Seite
1/20
Nächste Seite
Page | 13
Installation / projector mounting
CAUTION Danger to life!
During the installation, the
Provisions of the BGV C1 and EN 60598-2-17!
The suspension devices of the projector must be designed and dimensioned so that they can
withstand 10 times the payload for 1 hour without permanent harmful deformation.
The installation must always be carried out with a second independent suspension, For example, a
suitable fishing net. This second suspension must be designed and installed in such a way that no
part of the installation can fall in the event of a failure of the main suspension.
During the assembly, conversion and dismantling, the unnecessary stay in the area of movement
areas, lighting bridges, high-level workplaces and other hazardous areas is prohibited.
The contractor shall ensure that safety and technical equipment is inspected by experts prior to first
commissioning and after major modifications before commissioning.
The contractor has to ensure that safety engineering and mechanical engineering equipment is
inspected at least every four years by an expert in the scope of the acceptance test.
The contractor has to ensure that safety and mechanical equipment.
Method:
The projector should ideally be installed outside the area where people are sitting.
IMPORTANT! OVERHEAD ASSEMBLY REQUIRES A HIGH MEASUREMENT OF EXPERIENCE. This
includes (but is not limited to) calculations to define the load bearing capacity, the installation
material used and regular safety inspections of the material and the projector used. Never attempt
to perform the installation yourself if you do not have such a qualification; Plumber. Improper
installation may result in injury and / or damage to property.
The projector must be installed outside the hand area of people.
If the projector is to be suspended from the ceiling or high beams, etc., it is necessary to work with
the traverse system. The projector must never be mounted free-swinging in the room.
Danger: Projectors can cause serious injuries when falling! If you are in doubt about the security of a
possible installation, DO NOT install the projector!
Before mounting, make sure that the mounting surface can withstand at least 10 times the load on
the projector.
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Etec LED Quad Moving Head BEAM BAR RGBW wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info