Bedienungsanleitung Etna 1611vwt (Seite 39 von 48) (Deutsch, Englisch, Holländisch, Französisch)

324302

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

- the earth connection is in good working or-

der.

If the socket is not easily accessible, the in-

stallation engineer must provide a switch with

a contact breaking gap of 3 mm or more.

If the appliance power lead is not fitted with

a plug, use an approved standard type, re-

membering that:

- the green-yellow wire must be used for the

earth connection;

- the blue wire is the neutral;

- the brown wire is live;

- the lead must never touch hot surfaces over

about 75 degrees C;

- replacement leads must be of type H05RR-

F or H05V2V2-F of suitable size (see dia-

grams in fig. 2).

- if the appliance is supplied without lead,

using type H05RR-F or H05V2V2-F cable

of suitable size (see diagrams in fig. 2).

IMPORTANT: the manufacturer declines all

liability for damage due to failure to comply

with the regulations and standards in force.

Check that the appliance is correctly con-

nected to the earth (see diagrams in fig. 2 at

the back of the manual).

FOR COOKERS WITH ELECTRIC IGNI-

TION

The correct gaps between the electrode and

the burner are shown in figures 4, 5 and 6.

If no spark is generated, do not keep on try-

ing as this might damage the generator.

Possible causes of malfunctions:

- spark plug damp, dirty or broken;

- electrode-burner gap not correct;

- spark plug wire broken or without sheathing;

- spark discharging to earth (to other parts

of the cooker);

- generator or microswitch damaged;

- air has built up in the pipes (particularly if

the cooker has been out of use for a long

time);

- air-gas mixture incorrect (poor fuel setting).

THE SAFETY DEVICE

The correct gap between the end of the ther-

mocouple sensor and the burner is shown in

figures 4, 5 and 6.

To check that the valve is working properly,

proceed as follows:

- ignite the burner and leave it to work for

about 3 minutes;

- turn off the burner by returning the knob to

off position ( );

- after 90 seconds for hob burners, 60 sec-

onds for oven and grill burners, turn the

knob pointer to the "on" position;

- release the knob in this position and move

a burning match towards the burner; IT

MUST NOT IGNITE.

Time needed to excite the magnet during

ignition: 10 seconds approx.

Automatic tripping time, after flame has been

turned off: not more than 90 seconds for hob

burners; not more than 60 seconds for oven

and grill burners.

IMPORTANT

- Before doing any work inside the cooker,

disconnect the mains plug and shut the gas

tap.

- Never use matches to check the gas cir-

cuit for leaks. If a specific control device is

not available, foam or very soapy water can

be used.

- When re-closing the hob, check that the

electrical wires of the spark plugs (if

present) are not close to the injectors, so

that they cannot run across them.

Installation

334821/01 20-11-2001, 17:1939

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Etna 1611vwt Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info