Bedienungsanleitung Etna 4449t (Seite 3 von 18) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

128670

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

- 4 -

GENERAL

Carefully read the following important information regarding installation

safety and maintenance. Keep this information booklet accessible for

further consultations.

This apparatus was designed to be used in the suction version (air

evacuated externally), in the filter version (internal air recycling) or

in centralized exhausting version.

SAFETY PRECAUTION

1. Take care when the cooker hood is operating simultaneously with an

open fireplace or burner that depend on the air in the environment and

are supplied by other than electrical energy, as the cooker hood removes

the air from the environment which a burner or fireplace need for

combustion. The negative pressure in the environment must not exceed

4Pa (4x10

-5

bar). Provide adequate ventilation in the environment for

a safe operation of the cooker hood.

Follow the local laws applicable for external air evacuation.

2. WARNING !

In certain circumstances electrical appliances may be a danger

hazard.

A) Do not check the status of the filters while the cooker hood

is operating

B) Do not touch the light bulbs after appliance use

C) Flambè cooking is prohibited underneath the cooker hood

D) Avoid free flame, as it is damaging for the filters and a fire

hazard

E) Constantly check food frying to avoid that the overheated

oil may become a fire hazard

F) Disconnect the electrical plug prior to any maintenance.

G) This appliance is not intended for use by young children or

infirm persons without supervision

H) Young children should be supervised to ensure they do not

play with the appliance

I) There shall be adequate ventilation of the room when the

rangehood is used at the same time as appliances burning gas

or other fuels

L) There is a risk of fire if cleaning is not carried out in accordance

with the instructions

INSTALLATION INSTRUCTIONS

• Electric Connection

The appliance has been manufactured as a class II, therefore no earth

cable is necessary.

The connection to the mains is carried out as follows:

BROWN = L line

BLUE = N neutral

If not provided, connect a plug for the electrical load indicated on the

description label. Where a plug is provided, the cooker hood must be

installed in order that the plug is easily accessible.

An omnipolar switch with a minimum aperture of 3mm between

contacts, in line with the electrical load and local standards, must be

placed between the appliance and the network in the case of direct

connection to the electrical network.

• The appliance must be installed at a minimum height of 650 mm from

an cooker stove in case of a gashob or an electrical hob.

If a connection tube composed of two parts is used, the upper part must

be placed outside the lower part.

Do not connect the cooker hood exhaust to the same conductor used

to circulate hot air or for evacuating fumes from other appliances

generated by other than an electrical source.

• Mounting the cooker hood to the wall

Drill holes A-B-C-D according to indications quoted in (fig. 3).

Use screws and screw anchors suitable for wall (e.g. reinforced

cement, plasterboard) for the mounting of the cooker hood.

Where screws and screw anchors are supplied ensure that they are

suitable for the type of wall where the cooker hood is to be mounted.

Lock in the flange connector Y to the cooker hood (fig. 2).

Affix the bracket Z to the wall via the drill holes A (fig. 4).

Hang the cooker hood on the wall using the drill holes C (fig. 3).

Fasten the cooker hood using the fastening drill holes D (fig. 3).

• Exhausting Version

Connect the flange Y to the discharge opening with a connecting tube

(do not carry out for filter version).

Thread the upper connector E to the inside of the lower connector F;

hang the two connectors inserting them vertically on the cooker hood

locking the lower connector F to the wall using the drill holes B (fig. 3),

unthread the upper connector E towards the top, locking it in with the

appropriate screws in the drill holes G of the bracket Z (fig. 2) previously

affixed to the wall via the drill holes A (fig. 3).

In order to transform your cooker hood from exhausting version to

filter version, ask your local retailer for active carbon filters and then

carry out instructions for mounting filter version cooker hood.

• Filter Version

Install the cooker hood and the two connectors as described in the

paragraph mounting the exhausting version cooker hood.

To mount the filter connector refer to instructions included in the kit.

If the kit is not supplied, then order the kit as an accessory from your

local dealer.

The filters must be fitted to the fan unit placed inside the cooker hood.

The air is replaced in the environment via the eyelets impressed on the

connector E.

• Centralized exhausting version

This version is used in habitations

with centralized suction systems.

The switch controls the opening and closing of a valve via a thermo-

electric device. Turning the switch to the ON position, after 60 sec-

onds, will effect the opening of the valve to a 90° rotation permitting the

suction of the stale air externally. Turning the switch to the OFF posi-

tion, after 100 seconds, will effect the closing of the valve.

USE AND MAINTENANCE

• It is recommended to operate the appliance prior to cooking.

It is recommended to leave the appliance in operation for 15 minutes

after cooking is terminated in order to completely eliminate cooking

vapours and odours.

The proper function of the cooker hood is conditioned by the regularity

of the maintenance operations, in particular, the active carbon filter.

• The anti-grease filters capture the grease particles suspended in the

air, and are therefore subject to clogging according to the frequency of

the use of the appliance.

In order to prevent fire hazard, it is recommendable to clean the filter

at a maximum of 2 months by carrying out the following instructions:

- Remove the filters from the cooker hood and wash them in a solution

of water and neutral liquid detergent, leaving to soak.

- Rinse thoroughly with warm water and leave to dry.

- The filters may also be washed in the dishwasher.

The aluminium panels may alter in colour after several washes. This

is not cause for customer complaint nor replacement of panels.

• The active carbon filters purify the air that is replaced in the

environment. The filters are not washable nor re-useable and must be

replaced at maximum every four months. The saturation of the active

carbon filter depends on the frequency of use of the appliance, by the

type of cooking and the regularity of cleaning the anti-grease filters.

• Clean the fan and other surfaces of the cooker hood regularly using

a cloth moistened with denatured alcohol or non abrasive liquid

detergent.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR

EVENTUAL DAMAGES CAUSED BY BREACHING THE ABOVE

WARNINGS.

ENGLISH

Etna 4449t Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info