Bedienungsanleitung Etna A 410 WT (Seite 3 von 19) (Deutsch, Englisch, Holländisch, Französisch)

108300

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

ENGLISH

GENERAL

Carefully read the following important information regarding

installation safety and maintenance. Keep this information booklet

accessible for further consultations.

The appliance has been designed as a exhausting version

(external exhaust) or as a filter version (internal air recycle) cooker

hood.

SAFETY PRECAUTION

1. ake care when the cooker hood is operating simultaneously

with an open fireplace or burner that depend on the air in the

environment and are supplied by other than electrical energy, as

the cooker hood removes the air from the environment which a

burner or fireplace need for combustion.

The negative pressure in the environment must not exceed 4 Pa

(4 x 10 -5 bar).

Provide adequate ventilation in the environment for a safe

operation of the cooker hood.

Follow the local laws applicable for external air evacuation.

2. WARNING!!

In certain circumstances electrical appliances may be a

danger hazard.

A) Do not check the status of the filters while the cooker

hood is operating

B) Do not touch the light bulbs after appliance use

C) Flambè cooking is prohibited underneath the cooker hood

D) Avoid free flame, as it is damaging for the filters and a fire

hazard

E) Constantly check food frying to avoid that the overheated

oil may become a fire hazard

F) Disconnect the electrical plug prior to any maintenance.

INSTALLATION INSTRUCTIONS

• Electric Connection

The appliance has been manufactured as a class II, therefore no

earth cable is necessary.

The connection to the mains is carried out as follows:

BROWN = L line

BLUE = N neutral

If not provided, connect a plug for the electrical load indicated on

the description label. Where a plug is provided, the cooker hood

must be installed in order that the plug is easily accessible.

An omnipolar switch with a minimum aperture of 3mm between

contacts, in line with the electrical load and local standards, must

be placed between the appliance and the network in the case of

direct connection to the electrical network.

• The appliance must be installed at a minimum height of 650 mm

from an cooker stove.

If a connection tube composed of two parts is used, the upper

part must be placed outside the lower part.

Do not connect the cooker hood exhaust to the same conductor

used to circulate hot air or for evacuating fumes from other

appliances generated by other than an electrical source.

ATTENTION: should the lamps not work, make sure they are well

tightened.

MOUNTING OF THE HOOD IN THE LOWER PART OF AN

HANGING CUPBOARD

Drill 4 holes of 6 mm. diameter at the bottom of the hanging cupboard

as showed in the drawing fig.1.

Fit the hood in the cabinet with 4 screws, which are appropriate to that

kind of cupboard.

The appliance is provided with 2 air outlets, one which is in the upper

part and the other on the back. Both of them can be used according to

your requirements. A connecting ring (C), which to join the connecting

pipe to,and a cover (A) to close the air outlet, which is not used, are

supplied.

MOUNTING OF THE HOOD ON THE WALL

Drill 4 holes on the wall, which correspond to the position (B-Z) of the

drawing fig. 1.

Hang the hood on the 2 holes by using the screws and dowels with

expanding plug ,which are aprropriate for that kind of wall (ex.

concrete, plasterboard etc.)

Fix definitely the hood through the 2 security holes (Z).

CHANGING FROM EXHAUSTING HOOD TO FILTERING ONE

In order to make this change, demand a set of carbon filters to your

dealer. Active carbon filters are necessary to depurate the air, that will

be released in the room. Filters are not washable; they cannot be

regenerated and have to be replaced at most every 4 months. The

saturation of the activated charcoal depends on the more or less

prolonged use of the hood, on the type of cooking and on the regularity

of cleaning the grease filter. The filter (D) has to be applied to the

aspirating group, which is inside the hood hiting the centre of the group

with it and turning it of 90 degrees until the stop click is heard to lock

it. Remove the grill (G) to carry out this operation. Close with the

appropriate covers the upper and back air outlets; turn the small lever

(L) from the position (A) to the position (F). In this way the hood is

ready for the filtering function.

USE AND MAINTENANCE

• It is recommended to operate the appliance prior to cooking.

It is recommended to leave the appliance in operation for 15 minutes

after cooking is terminated in order to completely eliminate cooking

vapours and odours.

The proper function of the cooker hood is conditioned by the regularity

of the maintenance operations, in particular, the active carbon filter.

• The anti-grease filters capture the grease particles suspended in the

air, and are therefore subject to clogging according to the frequency of

the use of the appliance.

In order to prevent fire hazard, it is recommendable to clean the filter

at a maximum of 2 months by carrying out the following instructions:

- Remove the filters from the cooker hood and wash them in a solution

of water and neutral liquid detergent, leaving to soak.

- Rinse thoroughly with warm water and leave to dry.

- The filters may also be washed in the dishwasher.

The aluminium panels may alter in colour after several washes. This

is not cause for customer complaint nor replacement of panels.

• The active carbon filters purify the air that is replaced in the

environment. The filters are not washable nor re-useable and must be

replaced at maximum every four months. The saturation of the active

carbon filter depends on the frequency of use of the appliance, by the

type of cooking and the regularity of cleaning the anti-grease filters.

• Clean the fan and other surfaces of the cooker hood regularly

using a cloth moistened with denatured alcohol or non abrasive

liquid detergent.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR

EVENTUAL DAMAGES CAUSED BY BREACHING THE ABOVE

WARNINGS.

ENGLISH

Etna A 410 WT Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info