Bedienungsanleitung Etna A 4451 T (Seite 16 von 20) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

108693

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

- 17 -

the lower chimney piece pipe to the inside of the hood, using screws

P (Fig.14). Re-locate the filters in their seat.

USE AND MAINTENANCE

• It is recommended to operate the appliance prior to cooking.

It is recommended to leave the appliance in operation for 15 minutes

after cooking is terminated in order to completely eliminate cooking

vapours and odours.

The proper function of the cooker hood is conditioned by the regularity

of the maintenance operations, in particular, the active carbon filter.

• The anti-grease filters capture the grease particles suspended in the

air, and are therefore subject to clogging according to the frequency of

the use of the appliance.

In order to prevent fire hazard, it is recommendable to clean the filter

at a maximum of 2 months by carrying out the following instructions:

- Remove the filters from the cooker hood and wash them in a solution

of water and neutral liquid detergent, leaving to soak.

- Rinse thoroughly with warm water and leave to dry.

- The filters may also be washed in the dishwasher.

The aluminium panels may alter in colour after several washes. This

is not cause for customer complaint nor replacement of panels.

• The active carbon filters purify the air that is replaced in the environ-

ment. The filters are not washable nor re-useable and must be re-

placed at maximum every four months. The saturation of the active

carbon filter depends on the frequency of use of the appliance, by the

type of cooking and the regularity of cleaning the anti-grease filters.

• Clean the fan and other surfaces of the cooker hood regularly using

a cloth moistened with denatured alcohol or non abrasive liquid deter-

gent.

• The illumination installation is designed for use during cooking and

not for prolonged general illumination of the environment. Prolonged

use of the illumination installation notably reduces the duration of the

bulb.

COMMANDS: (Fig.18)

Push-button A = on/off lights switch

Push-button B = on/off cooker hood switch. The appliance switches

on at speed level 1, If the cooker hood is on depress the push-button

for 2 sec. to switch off the cooker hood. If the cooker hood is at speed

level 1 it will not be necessary to depress the push-button to switch the

cooker hood off. Decreases the motor speed.

Display C = indicates the motor speed level selected and activates the

timer.

Push-button D = switches on the cooker hood. Increases the motor

speed. Touching the key at 3rd speed, the intensive function runs for

10', then the appliance go back to work at the original speed. During this

function the display blinks.

Key E = The Timer times the functions on activation for 15 minutes,

after which they are switched off. The Timer is deactivated by re-

pressing Key E. When the Timer is activated the decimal point must

flash on the display. The Timer cannot be activated if the intensive

speed is functioning.

The “clean air” function is activated by pressing key E for 2 seconds

when the appliance is switched off. This switches the motor on for 10

minutes every hour at the first speed. During functioning a rotary move-

ment of the peripheral segments must be visualised on the display.

When this time has passed the motor switches off and the fixed letter

“C” must be visualised on the display until the motor re-starts after 50

minutes for another 10 minutes and so on. Press any key apart from the

light keys to return to normal functioning. Press key E to deactivate the

function.

• Active carbon/grease filter saturation:Fig.18

- When display item C flashes, at a speed where it alternates with the

letter F (e.g. 1 and F), the grease filters must be washed.

- When display item C flashes, at a speed where it alternates with the

letter A (e.g. 1 and A), the carbon filters must be replaced.

After the clean filter has been positioned correctly, the electronic memory

must be reset by pressing button A for approximately 5 seconds, until

the indication F or A shown on the display C stops flashing.

• COMMANDS: ELECTRONIC (Fig.19 A):

A = LIGHT

B = OFF/SPEED I

C = SPEED II

D = SPEED III

E = A

UTOMATIC STOP TIMER – 15 minutes (*)

F = FILTER SATURATION RESET LIGHT

When the “filter saturation” light flashes, the anti-grease filters must be

washed.

When the light comes on without flashing, the anti-grease filters must

be washed and the carbon filters replaced (in case of operation whit the

recycling version).

When this operation has been completed, press the key to reset it.

• COMMANDS:

(Fig.20) LUMINOUS

(Fig.19 B) ELECTRONICthe key symbols are explained below:

A = LIGHT

B = OFF

C = SPEED I

D = SPEED II

E = SPEED III

F = AUTOMATIC STOP TIMER - 15 minutes (*)

• If your appliance does not have the INTENSIVE speed function, press

key E for two seconds and it will be activated for 10 minutes after which

it will return to the previously set speed.

When the function is active the LED flashes. To interrupt it before

the 10 minutes have expired press key E again.

• By pressing key F for two seconds (with the hood switched off) the

“clean air” function is activated. This function switches the appliance

on for ten minutes every hour at the first speed. As soon as this function

is activated the motor starts up at the first speed for ten minutes, During

this time key F and key C must flash at the same time.

After ten minutes the motor switches off and the LED of key F remains

switched on with a fixed light until the motor starts up again at the first

speed after fifty minutes and keys F and C start to flash again for ten

minutes and so on.

By pressing any key for the exclusion of the hood light the hood will

return immediately to its normal functioning (e.g. if key D is pressed

the “clean air” function is deactivated and the motor moves to the 2nd

speed straight away. By pressing key B the function is deactivated).

(*) The “automatic stop timer” delays stopping of the hood, which

will continue functioning for 15 minutes at the operating speed set at the

time this function is activated.

• Active carbon/grease filter saturation: Fig.19B / Fig.20

- When button A flashes at a frequency of 2 seconds, the grease filters

must be cleaned.

- When button A flashes at a frequency of 0.5 seconds, the carbon

filters must be replaced.

After the clean filter has been replaced, the electronic memory must

be reset by pressing button A for approximately 5 seconds, until the

light on the button stops flashing.

•COMMANDS:(Fig.21A)MECHANICAL_(Fig.21B) Elliptic the key

symbols are explained below:

A = LIGHT

B = OFF

C = SPEED I

D = SPEED II

E = SPEED III

G = MOTOR WORKING indicator

THE MANUF

ACTURER DECLINES ALL RESPONSIBILITY FOR

EVENTUAL DAMAGES CAUSED BY BREACHING THE ABOVE

WARNINGS.

Etna A 4451 T Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info