Bedienungsanleitung Etna a4451 (Seite 15 von 20) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

129234

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

- 16 -

GENERAL

Carefully read the following important information regarding installa-

tion safety and maintenance. Keep this information booklet accessible

for further consultations.

The appliance has been designed for use in the ducting version (air

exhaust to the outside – Fig.1B), filtering version (air circulation on the

inside – Fig.1A) or with external motor (Fig.1C).

SAFETY PRECAUTION

1. Take care when the cooker hood is operating simultaneously with an

open fireplace or burner that depend on the air in the environment and

are supplied by other than electrical energy, as the cooker hood re-

moves the air from the environment which a burner or fireplace need

for combustion. The negative pressure in the environment must not

exceed 4Pa (4x10-5 bar). Provide adequate ventilation in the environ-

ment for a safe operation of the cooker hood.

Follow the local laws applicable for external air evacuation.

Before connecting the model to the electricity network:

- control the data plate (positioned inside the appliance) to ascertain

that the voltage and power correspond to the network and the socket is

suitable. If in doubt ask a qualified electrician.

If the power supply cable is damaged, it must be replaced with another

cable or a special assembly, which may be obtained direct from the

manufacturer or from the Technical Assistance Centre.

2. WARNING !

In certain circumstances electrical appliances may be a danger

hazard.

A) Do not check the status of the filters while the cooker hood

is operating

B) Do not touch bulbs or adjacent areas, during or straight after

prolonged use of the lighting installation.

C) Flambè cooking is prohibited underneath the cooker hood

D) Avoid free flame, as it is damaging for the filters and a fire

hazard

E) Constantly check food frying to avoid that the overheated

oil may become a fire hazard

F) Disconnect the electrical plug prior to any maintenance.

G) This appliance is not intended for use by young children or

infirm persons without supervision

H) Young children should be supervised to ensure they do not

play with the appliance

I) There shall be adequate ventilation of the room when the

rangehood is used at the same time as appliances burning gas

or other fuels

L) There is a risk of fire if cleaning is not carried out in accord-

ance with the instructions

This appliance conforms to the European Directive EC/2002/96, Waste

Electrical and Electronic Equipment (WEEE). By making sure that

this appliance is disposed of in a suitable manner, the user is helping

to prevent potential damage to the environment or to public health.

The

symbol on the product or on the accompanying

paperwork indicates that the appliance should not be treated as domestic

waste, but should be delivered to a suitable electric and electronic

appliance recycling collection point. Follow local guidelines when

disposing of waste. For more information on the treatment, re-use and

recycling of this product, please contact your local authority, domestic

waste collection service or the shop where the appliance was

purchased.

INSTALLATION INSTRUCTIONS

Assembly and electrical connections must be carried out by

specialised personnel.

• Electric Connection

The appliance has been manufactured as a class II, therefore no earth

cable is necessary.

The connection to the mains is carried out as follows:

BROWN = L line

BLUE = N neutral

If not provided, connect a plug for the electrical load indicated on the

description label. Where a plug is provided, the cooker hood must be

installed in order that the plug is easily accessible.

An omnipolar switch with a minimum opening of 3mm between con-

tacts, in line with the electrical load and local standards, must be placed

between the appliance and the network in the case of direct connection

to the electrical network.

• The minimum distance between the support surfaces of the cooking

pots on the cooker top and the lowest part of the cooker hood must be

at least 65 cm.

If a connection tube composed of two parts is used, the upper part must

be placed outside the lower part.

Do not connect the cooker hood exhaust to the same conductor used to

circulate hot air or for evacuating fumes from other appliances gener-

ated by other than an electrical source.

Before proceeding with the assembly operations, remove the anti-

grease filter(s) (Fig.16) so that the unit is easier to handle.

In the case of assembly of the appliance in the suction version prepare

the hole for evacuation of the air.

• Hood assembly

Remove the structure from the packaging and remove the 2 screws A

to separate the upper part from the lower part (fig.2).

- Position hole template on the ceiling paying attention that the arrow

is positioned on the same side as the appliance controls (Fig.3).

Make 4, Ø8 holes in the ceiling and drive in 3 screws without com-

pletely tightening them. Pay attention not to insert the screw into the

hole marked with an X on the hole template (the screws and expansion

plugs must be suitable for the type of wall).

- Take the upper part of the structure B (fig.4) and insert the 3 slots onto

the 3 screws that are not completely tightened.

Rotate slightly to fit (fig.4) .

Drive in the fourth screw X and tighten the remaining 3 to allow defini-

tive blocking of the upper part of structure B

- Take the lower part of the telescopic structure C and insert it into the

upper structure B (fig.5).

Adjust the height by referring to the amounts indicated in (fig.15) and

block it using the 8 screws G that are supplied (fig.6).

- Suction version: fix the flexible pipe to the prepared air evacuation

hole (fig 7).

- Filtering version: fix the flexible pipe to the deflector M and fix screw

I as indicated in (Fig.8), the active carbon filters must be applied to the

suction unit positioned inside the hood (Fig.17).

- Mount the connecting flange F in the upper part of the hood’s suction

unit using the 2 screws E (fig.9).

- Take the upper chimney piece and fix it to the structure using the 2

screws A (Fig.10).

Join the lower chimney piece with the upper one and fix it carefully

using adhesive tape L (Fig.11a).

- Unscrew the 2 screws O, max 3 mm (Fig.11a).

Insert the suction unit inside the structure paying attention that the

previously unscrewed screws O, hook into the slots in the lower part

as indicated in (Fig.11b).

Drive in the 3 screws N (supplied) and tighten the 2 screws O (Fig.11b).

- Fix the air evacuation pipe H (not supplied) onto the connection flange

F (Fig.12)

- Remove adhesive tape L and rest the lower chimney piece above the

cooker hood (Fig.13).

-If the cooker hood is supplied with a lower chimney piece that must

be fixed to the hood body with screws, remove the anti-grease filters

from the hood by acting on the relevant handles (Fig.16). Then screw

ENGLISH

Etna a4451 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info