Bedienungsanleitung Etna AK2378DC (Seite 16 von 20) (Englisch)

558370

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

444334

Fault: Cause/Remedy

The appliance does not

operate after connection to the

mains:

• Check if there is power in the socket and if the appliance is

switched on.

Cooling system operates

continuously without

intermittent stoppages:

• Ambient temperature too high.

• Frequent opening of the door, door open too long.

• Door not closed properly (particle between door gasket, sagged

door, check gasket sealing, etc...).

• Excessive quantity of fresh food inserted at once.

• Refrigerator probe (A) is clogged with fresh food. Relocate the food to

provide air circulation around the probe (certain models only).

• Check air circulation for sufﬁ cient cooling of the compressor, and

clean the condenser.

Excessive ice formation at the

rear interior wall of the freezer:

• Frequent opening of the door, door open too long.

• Inserting hot food in the freezer.

• Food or dish is touching the rear interior panel of the refrigerator.

• Bad door sealing; clean or replace the gasket if dirty or damaged.

Build-up of ice or frost in the

freezer interior may be a result

of the following:

• Door opened too frequently or too long.

• Door not properly closed.

• Poor door sealing.

• If the seal is dirty or damaged, clean or replace it.

Water dripping from the

appliance:

• Drain outlet is clogged, drain water drips past the collection groove.

• Clean the clogged outlet using plastic straw.

• Thaw thick ice deposits manually (see chapter Defrosting).

Difﬁ cult door opening: • If you attempt to open the immediately closed door of the freezer

you may experience resistance. This happens because certain

quantity of cold air escapes from the appliance through the open

door and is replaced by warm ambient air. Cooling of such air

creates negative pressure (vacuum) and suction, which prevents

easy opening of the door. Situation is normalized after a few

minutes (5-10), and you can open the door with ease.

Bulb replacement:

• Before replacing the light bulb, disconnect the appliance form the

power supply (pull the power cord from the wall socket).

Insert the screwdriver into the cover slot, lift it and remove the

cover.

Replace the bulb with the equivalent new bulb (E 14, same voltage as

the original one) and replace the cover back to its position.

• Don’t forget: the old bulb does not belong to organic waste.

• Light bulb is consumption material and is not covered by the

warranty!

• Bulb lamps used in this appliance are special purpose lamps

selected for household appliances use only. They are not suitable for

household room illumination.

If none of the above reasons seems to match your problem, please contact the nearest service

center and state the type, model and serial number as indicated on the label with basic information

attached in the appliance interior.

Troubleshooting guide

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Etna AK2378DC Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Etna AK2378DC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info