Bedienungsanleitung Etna EN4500 (Seite 13 von 20) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

2872

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

- 13 -

GENERAL

Carefully read the following important information regard-

ing installation safety and maintenance. Keep this infor-

mation booklet accessible for further consultations.

The appliance has been designed for use in the ducting

version (air exhaust to the outside – Fig.1B), filtering

version (air circulation on the inside – Fig.1A) or with

external motor (Fig.1C).

SAFETY PRECAUTION

1. Take care when the cooker hood is operating simulta-

neously with an open fireplace or burner that depend on

the air in the environment and are supplied by other than

electrical energy, as the cooker hood removes the air

from the environment which a burner or fireplace need for

combustion. The negative pressure in the environment

must not exceed 4Pa (4x10-5 bar). Provide adequate

ventilation in the environment for a safe operation of the

cooker hood.

Follow the local laws applicable for external air evacua-

tion.

Before connecting the model to the electricity net-

work:

- control the data plate (positioned inside the appliance)

to ascertain that the voltage and power correspond to

the network and the socket is suitable. If in doubt ask a

qualified electrician.

2. WARNING !

In certain circumstances electrical appliances may be

a danger hazard.

A) Do not check the status of the filters while the

cooker hood is operating

B) Do not touch bulbs or adjacent areas, during or

straight after prolonged use of the lighting installation.

C) Flambè cooking is prohibited underneath the cooker

hood

D) Avoid free flame, as it is damaging for the filters

and a fire hazard

E) Constantly check food frying to avoid that the over-

heated oil may become a fire hazard

F) Disconnect the electrical plug prior to any mainte-

nance.

G) This appliance is not intended for use by young

children or infirm persons without supervision

H) Young children should be supervised to ensure they

do not play with the appliance

I) There shall be adequate ventilation of the room

when the rangehood is used at the same time as appli-

ances burning gas or other fuels

L) There is a risk of fire if cleaning is not carried out

in accordance with the instructions

INSTALLATION INSTRUCTIONS

Assembly and electrical connections must be carried

out by specialised personnel.

• Electric Connection

The appliance has been manufactured as a class II,

therefore no earth cable is necessary.

The connection to the mains is carried out as follows:

BROWN = L line

BLUE = N neutral

If not provided, connect a plug for the electrical load

indicated on the description label. Where a plug is pro-

vided, the cooker hood must be installed in order that the

plug is easily accessible.

An omnipolar switch with a minimum opening of 3mm

between contacts, in line with the electrical load and

local standards, must be placed between the appliance

and the network in the case of direct connection to the

electrical network.

• The minimum distance between the support surfaces of

the cooking pots on the cooker top and the lowest part of

the cooker hood must be at least 65 cm.

If a connection tube composed of two parts is used, the

upper part must be placed outside the lower part.

Do not connect the cooker hood exhaust to the same

conductor used to circulate hot air or for evacuating

fumes from other appliances generated by other than an

electrical source.

Before proceeding with the assembly operations, remove

the anti-grease filter(s) (Fig.7) so that the unit is easier

to handle.

In the case of assembly of the appliance in the suction

version prepare the hole for evacuation of the air.

• FIXING TO THE WALL

Drill the holes A respecting the distances indicated (Fig.2).

Fix the appliance to the wall and align it in horizontal

position to the wall units. When the appliance has been

adjusted, definitely fix the hood using the screws A (Fig.5).

For the various installations use screws and screw an-

chors suited to the type of wall (e.g. reinforced concrete,

plasterboard, etc.). If the screws and screw anchors are

provided with the product, check that they are suitable for

the type of wall on which the hood is to be fixed.

• FIXING THE DECORATIVE TELESCOPIC FLUE

Arrange the electrical power supply within the dimensions

of the decorative flue. If your appliance is to be installed in

the ducting version or in the version with external motor,

prepare the air exhaust opening. Adjust the width of the

support bracket of the upper flue (Fig.3). Then fix it to the

ceiling using the screws A (Fig.3) in such a way that it is in

line with your hood and respecting the distance from the

ceiling indicated in Fig.2. Connect the flange C to the air

exhaust hole using a connection pipe (Fig.5).

Insert the upper flue into the lower flue. Fix the lower flue

to the hood using the screws B provided (Fig.5), extract

the upper flue up to the bracket and fix it with the screws

B (Fig.3).

If your appliance has the lower connections indicated as in

Fig. 4 A, the fixing to be carried out is that shown in Fig. 6

To transform the hood from a ducting version into a filtering

version, ask your dealer for the charcoal filters and follow

the installation instructions.

• FILTERING VERSION

Install the hood and the two flues as described in the

paragraph for installation of the hood in ducting version. To

assemble the filtering flue refer to the instructions con-

tained in the kit. If the kit is not provided, order it from your

dealer as accessory. The charcoal filters must be fitted in

the ducting unit located inside the hood (Fig.8).

ENGLISH

Etna EN4500 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info