Bedienungsanleitung Etna KGG673ZTA (Seite 8 von 16) (Deutsch, Englisch, Holländisch, Französisch)

692135

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Introduction

With this conversion-set you can convert your gas hob from

natural gas (G25.3 / 25 mbar) to propane/butane gas (G30 / 28-30

mbar). Before you start conversion, check whether your gas hob is genu-

inely set to natural gas.

Tools

A. Leak spray and/or special

pressure gauge

B. Tube- (or open end spanner 7)

C. Screwdriver 2 mm (blade width)

Attention: Check the gas tightness

after converting the appliance

(see chapter 2).

Replace the following parts:

- injector for the burners

- 2 data labels with the modiﬁed gas setting

Dismantling

Prevent damage of the work top. Lay down parts of the appliance on a

protected base.

1. Remove the pan supports, burner heads and the ornamental cover

(if present). See ﬁg. B.

2. Remove all injectors in the burners. See illustrations C and D.

Use a tubular spanner or open end spanner 7 for disassembling/

assembling the injector. Images C1 / C5 show the different types

of burners and injectors that can occur.

3. Pull up the control knobs vertically and remove them.

(see illustration E).

4. Use a metal plate or plier (see illustration C5) to remove the wok

injector on illustration C4.

Unlike the G25.3 version, the wok injector for G30-30 mbar has

the known smaller size (see illustration C2).

Converting

1. Replace the injectors (G30 - 28/30 mbar) in the burners (see

illustration F). Use a open end spanner 7 for disassembling/assembling

the injector.

For veriﬁcation, the values of the nozzles can be found in the table of

values for injectors (see p. 9).

2. Place the burner heads and connect the hob to a gas cylinder of

G30-30 mbar.

3. Using a small screwdriver, adjust the simmer setting with the simmer

setting screw. The gas tap’s simmer setting screw (ﬁg. G) is located on the

gas tap casing.The simmer setting screw on the gas tap casing is accessible

via the recess in the drip tray (ﬁg. G+H). The drip tray does not need to be

removed. Ignite the burner, turn the gas tap to ‘simmer setting’ and adjust

the ﬂames to a length of approx. 4mm (see ﬁg. I). Please note: the ﬂame

may not blow out in simmer setting. After adjusting, the ﬂame should

be stable. I.e., the burner may not blow out, for example, when fanned

manually.

4. Partially attach 2 data stickers on the current data sticker (with gas

type / gas tightness) to the bottom of the gas hob (see ﬁg. J+K).

5. Place the 3rd appliance identiﬁcation card on the front of the gas

hob manual (see ﬁgure L).

Warning!

Check the appliance for gas tightness, especially the injectors and

simmer setting screws!

Always check for gas tightness before using the appliance!

Deze kookplaat staat ingesteld

voor G30 / 28-30mbar (LPG).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Etna KGG673ZTA Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Etna KGG673ZTA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info