Bedienungsanleitung Etna t 4476l (Seite 14 von 18) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

133473

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

- 14 -

diameter of 150. If a pipe with a smaller diameter is used, the

e ciency of the product may be reduced and its operation

may become noisier.

Please note:

If your version of the appliance has decorative glass before

installing the hood, carry out the following steps as shown

in  gure 4:

1 - Remove both the cooker hood body B and the glass

panel A from the packaging and place them horizontally on

a secure surface.

2 - Take the glass panel A and position it above the cooker

hood body B.

3 - Fix the glass panel securely to the cooker hood body using

the 4 sleeves C and 4 screws D as indicated.

• Fixing to the wall

Drill the holes A respecting the distances indicated (Fig.2). Fix

the appliance to the wall and align it in horizontal position

to the wall units. When the appliance has been adjusted,

de nitely  x the hood using the screws A (Fig.5). For the vari-

ous installations use screws and screw anchors suited to the

type of wall (e.g. reinforced concrete, plasterboard, etc.). If

the screws and screw anchors are provided with the product,

check that they are suitable for the type of wall on which the

hood is to be  xed.

• Fixing the decorative telescopic  ue

warning! Caution! If your appliance model features the

lower connector with a tab, before  xing it in place bend

the tab inwards using a pair of pliers, as illustrated in  gure

5, step1.

Arrange the electrical power supply within the dimensions of

the decorative  ue. If your appliance is to be installed in the

ducting version or in the version with external motor, prepare

the air exhaust opening. Adjust the width of the support

bracket of the upper  ue (Fig.3). Then  x it to the ceiling using

the screws A (Fig.3) in such a way that it is in line with your

hood and respecting the distance from the ceiling indicated

in Fig.2. Connect the  ange C to the air exhaust hole using a

connection pipe (Fig.5 - Stage 2).

Insert the upper  ue into the lower  ue. Fix the lower  ue

to the hood using the screws B provided (Fig.5 - Stage 2),

extract the upper  ue up to the bracket and  x it with the

screws B (Fig.3).

To transform the hood from a ducting version into a  ltering

version, ask your dealer for the charcoal  lters and follow the

installation instructions.

• Filtering version

Install the hood and the two  ues as described in the paragraph

for installation of the hood in ducting version. To assemble the

 ltering  ue refer to the instructions contained in the kit.

If the kit is not provided, order it from your dealer as acces-

sory.

The  lters must be applied to the suction unit positioned inside

the hood. They must be centred by turning them 90 degrees

until the stop catch is tripped (Fig.8).

USE AND MAINTENANCE

• We recommend that the cooker hood is switched on before

any food is cooked. We also recommend that the appliance is

left running for 15 minutes after the food is cooked, in order

to thoroughly eliminate all contaminated air.

The effective performance of the cooker hood depends on

constant maintenance; the anti-grease filter and the active

carbon filter both require special attention.

• The anti-grease filter is used to trap any grease particles

suspended in the air, therefore is subject to saturation (the

time it takes for the filter to become saturated depends on

the way in which the appliance is used).

- To prevent potential fire hazards, the anti-grease filters

should be washed a minimum of every 2 months (it is

possible to use the dishwasher for this task).

- After a few washes, the colour of the filters may change. This

does not mean they have to be replaced.

If the replacement and washing instructions are not followed,

the anti-grease filters may present a fire hazard.

• The active carbon filters are used to purify the air which

is released back into the room. The filters are not washable

or re-usable and must be replaced at least once every four

months. The active carbon filter saturation level depends on

the frequency with which the appliance is used, the type of

cooking performed and the regularity with which the anti-

grease filters are cleaned.

• Clean the cooker hood frequently, both inside and outside,

using a cloth which has been dampened with denatured

alcohol or neutral, non-abrasive liquid detergents.

• The light on the cooker hood is designed for use during

cooking and not for general room illumination. Extended use

of the light reduces the average duration of the bulb.

• Replacing halogen light bulbs (Fig. 6).

To replace the halogen light bulbs B, remove the glass pane

C using a lever action on the relevant cracks.

Replace the bulbs with new ones of the same type.

Caution: do not touch the light bulb with bare hands.

•Commands: ( g.9) mechanical the key symbols are explained

below:

A = LIGHT

B = OFF

C = SPEED I

D = SPEED II

E = SPEED III

THE MANUFACTURER DECLINES ALL RESPONSIBILITY

FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE

ABOVE WARNINGS.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Etna t 4476l Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info