Bedienungsanleitung Eufab 11446 (Seite 4 von 12) (Deutsch, Englisch, Französisch, Italienisch)

807240

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

GB Expansion set for a third bicycle, suitable for CARLO PLUS, Article No. 11439

Article Number 11446

Overview

• Intended use • Scope of delivery • Specications • Safety notes • Operating instructions • Care and maintenance • Contact information

WARNING Read the operating instructions through carefully prior to initial use and observe all of the safety notes!

Not observing such may lead to personal injury, damages to the device or your property!

Store the original packaging, the receipt and these instructions so that they may be consulted at a later date!

Prior to initial use check the contents of the packaging to ensure that they are in perfect condition and complete!

Intended use

This retrotting set is used to extend the EUFAB trailer coupling rack CARLO PLUS, Article No. 11439, to include an additional space for a third

bicycle.

Scope of delivery

• 2 wheel rails

• 1 frame holder

• 2 wheel stoppers

• 4 end caps

• 3 small tensioning belts

• 1 tension relief strap with clamp lock and rubberised hook

• 4 carriage bolts with washers and self-tapping nuts

• Operating instructions

• Only for the EUFAB CARLO PLUS bicycle rack, article number 11439

• Weight: 1.195 kg

• Colour: Silver

Specications

Safety notes

1. Keep children away and do not allow children to operate this device!

2. Only use this product as intended!

3. Do not manipulate or dismantle the device!

4. For your own safety, only use accessories and spare parts that are stated in these Instructions or are recommended by the manufacturer!

Operating instructions

Installation of the expansion unit to the existing bicycle rack

Figure 1

Secure the wheel rails (105) using the carriage bolts (107), the washers (109) and the self-tapping nuts (108) to the lamp holders (009L) and

(009R) of your EUFAB CARLO PLUS bicycle rack. Fit the end caps (124) onto the ends of the rails.

Clip one wheel stopper to a wheel rail in such way that the high side of the wheel stopper faces the middle of the rack. Feed one short tensioning

strap (129) through the middle, side openings of the wheel stopper, from the top under the wheel rail and on the other side, from below through

the openings of the wheel stopper. The remaining strap is used later to correctly secure the front wheel of the third bicycle.

Securing the third bicycle

Secure the frame holder (014) to the frame of the second bicycle. Place the third bicycle in the wheel rail and secure it at the free end of the frame

holder. Slide the wheel stopper from the middle of the bike rack up to the bike tyre and secure the rear wheel with a short tensioning strap (129)

and the front wheel with two short tensioning straps (129) (see Figure 2). Now secure the bicycles with the long safety strap (included in the

scope of delivery of the bicycle rack). Wrap the safety strap through the bicycle frames and around the U-shaped bar and tighten (see Figure 3).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eufab 11446 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info