Bedienungsanleitung Eufab 11555 - Amber III (Seite 10 von 44) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

807227

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Inserting the license plate

Mounting the frame holder

Mounting the license plate holder

Undo the handle screw of the frame holder and rotate out fully. Open the cu

of the frame holder and place the inserts around the U-bracket at a position

suitable for your bicycle. Place the cu around the inserts and push  rmly

together. Close the frame holder using the handle screw (but do not tighten).

Remove the screws from the lamp mount before installing the license plate

holder and then mount the license plate holder.

The license plate holder must be at the same height as the lights.

Step 3

Components

Laying electrical cables

The mounting clips for securing the license plate are push-out parts in the

holder. Break out two of the clips. Slide the license plate into the holder, then

push the clips into the cut-outs to secure the license plate.

Attaching the plastic covers

Mounting the bicycle rack on the trailer tow bar

Fit the plastic covers onto the middle of the wheel rails.

Before you put the bicycle rack on the trailer tow bar, familiarise yourself with

the quick locking system.

Ensure that the trailer tow bar is undamaged, clean and free of grease.

The quick locking mechanism is a component with a lever. Activating the lever

opens or closes the quick locking mechanism. With the help of the securing

bolt and the padlock, the quick locking system may be locked and secured.

Mounting the short tensioning straps

Insert the short tensioning strap from the inside to the outside below the bike

holder and then from the outside to the inside through the slots of the bike

holder (see photograph).

Set bolt Lock nut

Set bolt Safety pin

Caution: You must tighten both knob nuts very  rmly to ensure that the

U-bracket is  ush against the U-bracket mount.

Lever

Lock

Clips Cut-outsCut-outs

The padlock must always be used as additional security

when using the bicycle rack.

Park your vehicle on a level surface.

Switch the motor o and pull on the brake.

Remove the securing bolt from the quick locking mechanism and rotate by

90° to prevent it from engaging again. Open the quick locking mechanism by

lifting the lever.

Place the rack, from above, horizontally onto the trailer tow bar. Push the

lever of the quick locking mechanism down (force required is approximately

35 - 40kg) as far as it will go (the lever will remain in the horizontal position).

Check whether the bike rack is securely and  rmly positioned on the trailer

tow bar and can no longer be rotated. If this is not the case, the quick locking

mechanism must be readjusted. Lift the lever and remove the rack from

Secure the cables of the lights to the underside of the rack using the supplied

cable ties. Make sure that the cables cannot be damaged when lowering and

raising the rack.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eufab 11555 - Amber III Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info