Bedienungsanleitung Eufab 16257 (Seite 11 von 36) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

806947

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Inserting the memory card

Make sure that the dashboard camera has been

switched o. Insert the micro-SD into the slot

(Position 2 in the overview). Pay attention to ensure

that the memory card is correctly positioned. The

contacts of the memory card must face in the direction

of the lens. Carefully push the memory card into the

slot until it engages with a soft click.

Clean the section of the windscreen where the camera

is to be mounted. Put the camera mount (Position 18

in the overview) into the mounting point (Position 6

in the overview) of the camera. Press the suction base

(Position 15 in the overview) against the windscreen.

Flip the lever (Position 16 in the overview). Undo the

coupling nut (Position 17 in the overview) on the ball

joint. Align the camera. Tighten the coupling nut up

again.

Plug the USB connector (Position 19 in the overview)

of the charging cable into the USB socket (Position 7

in the overview) of the camera. Lay out the charging

cable in such a way that it does not impede visibility

and does not hinder you during the journey. Plug the

vehicle connector (Position 20 in the overview) of the

charging cable into the 12 V socket of your vehicle.

Long press:

Switches the camera on/o.

Video recording is started directly after the camera is

switched on.

Brief press:

Switches the Power-LED (Position 5 in the overview)

on/o.

In Standby mode:

A brief press starts video recording (red dot ashes on

the display)

A second brief press stops video recording.

In Photo mode:

A brief press takes a photograph.

In Play mode:

A brief press plays the recorded video.

ON/OFF switch (Position 1 in the overview)

OK button (Position 10 in the overview)

Removing the memory card

Switch the camera o. To remove the memory card,

press down and release. The card will pop up and you

can remove it.

Removing the memory card with the

camera switched on may result in a loss of

data or damage to the device.

6.2 MEMORY CARD

6.3 INSTALLATION

6.4 CONNECTING THE CAMERA

6.5 FUNCTIONS

In Standby mode:

A brief press opens the menu for the video settings.

With the cursor buttons (Positions 11 and 13 in the

overview), you can select the various menu items.

Press the OK button to open the selected menu item.

Use the cursor buttons to select the setting in the

menu item, and conrm by pressing the OK button.

Settings in the video menu (symbol shows a

video camera in the top left of the display):

Resolution: FHD – HD - 720P 1280x720 - WVGA

848x480 - VGA 640x480

Loop recording:

Here, the camera records short video passages. When

the memory is full, the oldest recording will always be

deleted.

Switch o –1 minute –2 minutes –3 minutes –

5 minutes –10 minutes

Lighting compensation:

Here you can set the brightness of the video recording.

+2.0 …+0.0 … -2.0

Motion detector:

When the motion detector is activated, the

camera automatically starts recording when motion

is detected.

Switch o – switch on

Menu button (Position 3 in the overview)

19 USB connector

Figure 3: Charging cable

20 Vehicle connector

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eufab 16257 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info