Bedienungsanleitung Eufab 16518 - CB20 (Seite 10 von 24) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

807581

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Set the power switch to the "OFF" position.

6.2.5 REMOVING THE CHARGER

First pull the plug out of the socket and observe

the sequence for disconnection. This prevents

sparks from forming. Since charging generates

a detonating gas, this is particularly important

for the sake of your safety.

CAUTION

Disconnect the charger from the mains power supply.

Next, remove the black negative (-) cable. Now, remove the

red positive cable (+) from the positive pole of the battery.

Let the battery cool down.

Only for open batteries: Fill the cells with distilled water

up to the level speci ed by the battery manufacturer. Close

the battery cells with the stoppers.

The green 30 A  at fuse can blow if the pole clamps touch

each other when the unit is switched on.

In this case, switch the battery charger o and disconnect the

mains plug from the socket. Pull the fuse out of the holder

and replace it with a new, equivalent fuse.

6.3 TROUBLESHOOTING

6.3.1 IN CASE OF SHORT CIRCUIT

Figure 5: 30 A fuse

In the event of overvoltage in the power supply system, the

5 A glass fuse may blow. In this case, switch o the battery

charger and disconnect the mains plug from the socket.

Unscrew the fuse holder. Replace the fuse with a new

equivalent one

(Ø 5 x 20 T 5 A).

6.3.2 IN CASE OF OVERVOLTAGE

Figure 6: T 5 A fuse

If other faults or defects occur, contact our customer service

department (see section 9) or consult a specialist electrical

workshop.

6.3.3 OTHER FAULTS

Never open the device yourself to attempt

to repair it. This is potentially fatal!

The battery charger is maintenance-free when used in

accordance with the intended purpose.

7. MAINTENANCE AND CARE

7.1 MAINTENANCE

Clean the pole callipers after the charging process is

completed. Remove all splashed battery acid from the pole

callipers to prevent corrosion. Clean the device carefully with

a dry cloth. Do not use liquids or chemical cleaning agents.

Never submerge the device in liquid. Never allow liquids to

run over the device or to get inside.

Properly roll up the cable before storing the device to prevent

damage to the cables and the device. Store the device in a dry

and clean location.

7.2 CARE

The packaging is made up of environmentally

friendly materials which may be disposed of

via your local recycling points.

Do not put electrical devices into the

household waste.

Electrical and electronic scrap must be

collected separately and disposed of in an

environmentally responsible manner for

recycling. Please contact your community or

city administration regarding disposal options

for electronic scrap.

8. NOTES REGARDING ENVIRONMENTAL PROTECTION

9. CONTACT INFORMATION

EAL GmbH

Otto-Hausmann-Ring 107

42115 Wuppertal, Germany

+49 (0)202 42 92 83 0

+49 (0) 202 42 92 83 – 160

info@eal-vertrieb.com

www.eal-vertrieb.com

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eufab 16518 - CB20 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info