Bedienungsanleitung Eufab 21083 (Seite 8 von 27) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

807584

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

Connect the USB charging cable (Position 23 in the overview) with

the USB charging connection of the compressor (Position 4 in the

overview). Connect the other end of the USB charging cable to a USB

charger. The display for the battery charging status (Position 15 in the

overview) is activated in the display. During the charging process, the

segments of the charging status display shine one after another. Once

all four segments shine permanently, the compressor’s battery is fully

charged.

After charging,  rst disconnect the charger from the power socket

and then disconnect the compressor from the charging cable. Always

maintain this sequence.

6.2 CHARGING THE BATTERY

Setting the TARGET pressure

Press the ON/OFF switch (Position 20 in the overview) for approx. 3

seconds. The display light is activated. Pressing the selector switch

several times for a longer period (Position 22 in the

overview), you can set the unit for the pressure:

PSI BAR  KPA  KGF/CM²

6.3 USING THE COMPRESSOR

Checking the charge status

Press the ON/OFF switch. (Position 20 in the overview) for

approx. 3 seconds. The display is activated. The battery symbol

shows the charging status (empty, 25 %, 50 %, 75 %,

100 %).

You can set the target pressure with the buttons and

(Position 21 and 19 in the overview), these can be read in the display

‘TARGET’ (Position 17 in the overview).

Automatic/controlled lowering of the air pressure is not

possible with this device.

Connecting the air hose

Screw the end with the outer thread of the air hose (Position 24 in

the overview) into the connection of the compressor (Position 6 in the

overview).

Open the lock on the valve

connection

Lock the valve connection

Place the valve connection on the

valve

You can now  ll the tyres using the

compressor

Figure 2

Figure 4

Figure 3

Figure 5

Filling a tyre with the auto valve

If you want to  ll a tyre with the auto valve (Schrader valve), you do

not need any of the separate adapters.

Using the adapter

Bicycle valve adapter (for Dunlop and Sclaverand valves)

(Position 27 in the overview):

For Sclaverand valves: Undo the knurled screw of the valve piston

and push down brie y once.

Screw the valve adapter, using the knurled crown, down onto the

bicycle valve.

Place the valve connection of the air hose onto the bicycle valve

adapter, like the auto valve, Figures 2 to 5. You can now start the

compressor by pressing the ON/OFF switch and  ll the bicycle tyres. On

completion of the  lling process, remove the air hose and the adapter

from the valve.

For Sclaverand valves: Tighten the knurled screw of the valve piston

again.

Adapter for balls (Position 26 in the overview):

Place the adapter for balls into the valve connection as shown in Fig-

ures 2 to 5. Insert the adapter into the valve of the ball. Now you can

switch on the compressor and  ll the ball.

Universal adapter for recreational articles (Position 25 in the

overview):

Place the universal adapter into the valve connection of the air hose

as shown in Figures 2 to 5. Insert the universal adapter into the

 lling connection of your leisure equipment. Depending on version, it

is possible that the universal adapter will need to be held  rmly during

the  lling process.

Now you can switch on the compressor and start the  lling process.

Filling process

Press the ON/OFF switch for the compressor (Position 20 in the over-

view) to start the  lling process.

The compressor starts, the pressures can be read on the display during

the  lling process (Position 16 in the overview).

Once the set target pressure is reached, the compressor switches o .

Only allow the compressor to work without

interruption for maximum 5 minutes.

Then allow the compressor to cool down for at

least 15 minutes before continuing to work with

it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eufab 21083 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info