Bedienungsanleitung Eurogarden ES-EM 1032 (Seite 46 von 56) (Englisch, Italienisch)

724385

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

- 46 -

Warning!

This equipment generates an electromagnetic

ﬁ eld during operation. Under certain circumstan-

ces this ﬁ eld may actively or passively impede

medical implants. To reduce the risk of serious

or fatal injuries, we recommend persons with

medical implants to consult their doctor and the

manufacturer of the medical implant prior to using

the equipment.

5. Before starting the equipment

Before you connect the equipment to the mains

supply make sure that the data on the rating plate

are identical to the mains data.

Warning!

Always pull the power plug before making

adjustments to the equipment.

The lawn mower is delivered unassembled.

The complete push bar and the grass basket

must be assembled before using the lawn mower.

Follow the operating instructions step-by-step

and use the pictures provided as a visual guide to

easily assemble the equipment.

Fitting the wheels (Fig. 3a to 3d):

Follow Fig. 3a to 3d for ﬁ tting the wheels.

Fitting the push bar (Fig. 4a to 4c)

Take a bottom push bar (Fig. 2 /Item 14) and

fasten it with the screw (Fig. 2/Item 15) as shown

in Fig. 4a. Proceed in the same way on the other

side. Fasten the top push bar (Fig. 1/Item 1) to

the bottom push bar (Fig. 2/Item 14) as shown in

Fig. 4b.

Then attach the power cable to the push bar (Fig.

4c/Item A) using the cable clips (Fig. 2/Item 17).

Mounting the grass basket (Fig. 5a to 5b)

Plug the bottom and the top part of the grass box

together (Fig. 5a/Item 9, 10). Ensure that all the

plastic lugs engage correctly. Before you ﬁ t the

grass basket you must ensure that the motor is

switched oﬀ and the blade is not rotating.

The grass box must be attached to the two hooks

on the mower (Fig. 5b). To do this, open the ejec-

tor ﬂ ap with one hand (Fig. 5b/Item 4) and attach

the grass box with the other hand. The ejector ﬂ ap

is held against the grass box by a spring.

Adjusting the cutting height

Warning!

Adjust the cutting height only when the motor has

been switched oﬀ and the power cable has been

disconnected.

Before you begin to mow, check to ensure that the

blade is not blunt and that none of the fasteners

are damaged. To prevent any imbalance, replace

blunt and/or damaged blades. To carry out this

check, ﬁ rst switch oﬀ the motor and pull out the

power plug.

The cutting height is adjusted as shown in Figure

6. To do so, turn the equipment upside down or tilt

it to the side. Position both the front and rear axle

in the same notch, so that the cutting blade runs

parallel to the lawn.

Position Cutting depth

1 65mm

2 45mm

3 30mm

Power supply

The lawn mower can be connected to any light

socket-outlet with a 230-240 Volt alternating

current. However, the socket outlet must have an

earthing contact protected by a 16 A circuit brea-

ker. Additionally, a residual current device (RCD)

circuit-breaker with max. 30 mA must be used!

Power cable for the device

Please only use power cables that are not dama-

ged. The total length of the power cable should

not exceed 50 meters; going beyond this distance

will reduce the power output of the electric motor.

The power cable must have a cross-section of 3

x 1.5 mm

. The insulating sheath of lawn aerator

power cables is frequently damaged.

Some of the causes for this are:

•

Cuts caused by running over the cable

•

Pinching when the power cable is dragging

under doors and pulled through windows.

•

Cracking due to old age of the insulation

•

Kinking by improperly fastening or guiding the

power cable

The power cables must, at the very minimum, be

of type HO5RN-F and 3-stranded. The cable type

must be printed somewhere on the power cable.

Only purchase power cables that are marked as

such! Plugs and socket couplers for the power

cables must be made from rubber and be splash-

proof. There is a limit to how long power cables

Anl_ES_EM_1032_SPK7.indb 46Anl_ES_EM_1032_SPK7.indb 46 29.11.2018 15:34:5829.11.2018 15:34:58

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eurogarden ES-EM 1032 Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info