Bedienungsanleitung Eurom 800 (Seite 13 von 32) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

510020

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

 Now screw the wall support loosely to the wall and mark the location of the lower screws.

 Remove the wall support again and drill the lower holes and insert plugs.

 Screw the wall support to the wall and check whether it is secure and horizontal.

 Screw the fixing bracket with the small screw underneath the radiator so that the rectangular part

sticks out.

 Now hang the radiator in the wall support and mark the location for the screw through the fixing

bracket.

 Remove the radiator from the wall and drill a hole for the fixing bracket. Insert a plug.

 Hang the radiator on the wall and secure it with a screw through the fixing bracket and into the wall.

Tighten the screw as much as possible; there will be a few centimetres between the bracket and the

wall!

Set-up and Operation

 Make sure the heater is turned off (O) and that the thermostat dial is set to maximum (clockwise, as

far as it will go). Now plug into an earthed, correctly functioning 220-240V / 50Hz socket. Only

connect the heater to an earthed socket!

 Switch the radiator on by setting the output button to I (400W) or II (800W). The ON light will come on

and the radiator will start to work. For slow heating, a small rise in temperature or a small space,

choose setting I (400W). For quick heating, a bigger temperature rise or a larger space, choose

setting II (800W).

 When the space has reached the desired temperature, turn the thermostat dial anticlockwise slowly

until you hear a click. In this position, the thermostat will maintain the current temperature by turning

the heater on and off for a top-up, if necessary. If so desired, you can now switch to a lower power

level. For higher temperatures, turn the thermostat dial clockwise, for lower temperatures

anticlockwise.

 Switch the output button to O (off) to turn off. The heater switches off, the pilot light will turn off.

Unplug.

Safety features

In case of internal overheating, the overheating safeguard will switch the heater off. This may occur if

the heater cannot give off enough heat or if it cannot draw in enough fresh air. As mentioned above, this is

generally caused by (partially) covering the heater, obstructing the air intake and/or outlet grills or

installing the heater too close to a wall or something similar. In case of overheating, switch off the heater

and unplug. Give the heater time to cool down, remove the source of the overheating and use as normal.

If the problem persists or if you have not been able to trace the source of the overheating, turn the heater

off immediately and unplug. Contact a servicing point to have the heater repaired.

Cleaning and Maintenance

Keep the heater clean. Deposits of dust and dirt in the appliance are a common cause of overheating so

these should be removed regularly. Switch off the heater, remove the plug from the socket and allow the

heater to cool down before cleaning or carrying out maintenance work.

 Wipe the outside of the heater regularly with a dry or slightly damp cloth. Do not use aggressive

soaps, sprays, cleaners or abrasives, waxes, polishes or chemical solutions!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eurom 800 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info