Bedienungsanleitung Eurom Moonheater (Seite 12 von 32) (Deutsch, Englisch, Holländisch, Französisch, Schwedisch)

591472

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

24. The appliance (incl. cord and plug) may only be opened and/or repaired by properly

authorised and qualified persons.

25. Only use this heater for its intended purpose and as described in this instruction manual.

Not abiding by instructions 23, 24 and 25 may lead to damage, fire and/or personal injuries.

A failure to adhere to these rules also immediately nullifies the guarantee and vendor,

importer and/or manufacturer do not take responsibility for any of the consequences!

Description

1 – control dial

2 – thermostat dial

3 – air outlet grill

Location and Connection

 Remove all packaging material and keep

out of reach of children. After removing

packaging, check the appliance for

damage or other signs that could indicate

a fault/defect/malfunction. In case of

doubt, do not use the appliance, but contact your vendor for inspection or replacement.

 Choose a suitable location for the heater which is at least one metre away from any

obstructions, walls or inflammable materials (see also safety instructions).

 Make sure a functioning heater is always placed on a solid, flat and horizontal surface.

 Check if the control dial is set to 'OFF' (O).

 Fully extend the power cord and plug into a suitable 220-240V socket. To prevent the

circuit overloading, check that no other appliances are connected to the same group.

Set-up and Operation

 Turn the thermostat dial to maximum (clockwise as far as possible).

 Switch the heater on by turning the control dial to one of the following two positions:

I Heating at half power (1000W)

II Heating at full power (2000W)

It is most economical to heat the space at full power, then to switch to half power to

maintain the temperature.

 Both at half and full power, the fan rotates at the same speed; the difference between

the two lies in the number of heating elements in use.

 Once the desired temperature is reached, turn the thermostat dial back slowly until you

hear a click. The temperature is now set. The heater will automatically switch on and off

to maintain the set temperature. To set a higher or lower temperature, turn the

thermostat dial either clockwise or anticlockwise.

 To switch the heater off, set the power dial to ‘0’ (off). Unplug.

Safety features

In case of internal overheating, the overheating safeguard will switch the heater off. This

may occur if the heater cannot give off enough heat or if it cannot draw in enough fresh air.

As mentioned above, this is generally caused by (partially) covering the heater, obstructing

the air intake and/or outlet grills or installing the heater too close to a wall or something

similar. When the overheating safeguard switches the heater off, set the mode selector dial

to ‘0’ (off), unplug and allow the heater to cool down. Remove and/or amend the cause of

overheating and reuse the heater as normal. If you cannot find a cause and overheating

recurs, stop using the heater, and take it in for inspection/repair.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eurom Moonheater Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info