Bedienungsanleitung Eurom Multifan - ventilatorkachel (Seite 11 von 16) (Deutsch, Englisch, Holländisch, Französisch)

474874

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Description

A = Air intake rear

B = Air outlet

C = Operating button

D = Handle

Location and Connection

Remove all packaging material and keep out of reach of children. After removing packaging, check the appliance

for damage or other signs that could indicate a fault/defect/malfunction. In case of doubt, do not use the

appliance, but contact your vendor for inspection or replacement.

Freestanding:

• Choose a suitable location for the heater which is at least one metre away from any obstructions, walls or

inflammable materials (see also safety instructions).

• Make sure a functioning heater is always placed on a solid, flat and horizontal surface. Do not place the

heater on an uneven surface, such as a bed or sofa, and not on deep-pile carpet.

• Check if the control dial is set to 'OFF' (O).

• Fully extend the power cord and plug into a suitable 230V socket. To prevent the circuit overloading, check

that no other appliances are connected to the same group.

Wall mounting

The heater can also be wall-mounted. When wall-mounting the heater, the following points must be complied

with:

• Make sure the wall is totally vertical, sturdy, flat and incombustible, i.e. not timber, plasterboard, chipboard,

synthetic material or the like. When installing the heater, make sure there are no pipes or cables in the wall

that might be damaged.

• The heater should not be suspended from a ceiling or similar structure!

• Do not position the heater directly under, over, next to or in front of a power point.

• Make sure there is a minimum distance of 120 cm between the heater and the floor, 50 cm between the

heater and the ceiling and incombustible side walls, and a minimum of 120 cm between the heater and

combustible objects such as cupboards, shelves,

combustible side walls, curtains, furniture, etc. The

flow of air from the heater must not be obstructed in

any way.

When you have found a suitable location, install the

heater as follows:

• Drill two holes in the wall, 162 mm from each other and

exactly horizontal with each other. Insert one of the

wall-plugs provided into each hole and screw in one of

the (large) screws until 5 mm of the screw + the screw

head are left projecting from the wall.

• Use the small screw to attach the small locking plate

supplied to the rear of the heater, lower middle, into

the hole provided (see illustration).

• Now hang the heater with the two

hanging ‘eyes’ (top rear of heater)

on to the two horizontal screws, with the handle located up. Make sure that the protruding

screws fit snugly into the narrow part of the hanging ‘eyes’.

• On the wall, draw the location where the drill hole for the locking plate is to be made.

• Take the heater off the wall, drill the hole in the location indicated and insert a wall-plug.

• Hang the heater back on the wall and screw the final screw through the locking plate into the wall. Check to see

that the heater is firmly attached and is hanging fully horizontally. Only then may you operate the heater.

All of the safety instructions also apply to a heater that is already mounted!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eurom Multifan - ventilatorkachel Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info