Bedienungsanleitung Eurom Sani-Fanheat 2000 (Seite 21 von 56) (Deutsch, Englisch, Holländisch, Französisch, Schwedisch)

667887

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

therefore may not be used in a lying, leaning, hanging or standing position! The

wall on which the device is hung has to be firm, flat and perfectly vertical and

made from non-inflammable material that cannot melt. It has to be at least 20 cm

away from side walls and the bottom has to be at least 180 cm.

The heater has to preferably (and definitely in damp rooms) be positioned at and

permanently connected to an electric socket. This connection may only be made

by a qualified electrician and, for that reason, is not described here.

In this booklet, for reasons of safety, use with a plug should be assumed; when

there is a permanent connection, any passages about the plug do not apply.

 Drill 2 holes (7 mm.) in the wall at the selected spot: horizontal to one another with

a distance of 18,7 cm. Insert plugs into the holes and insert screws into the plugs

(included). Leave the screws protruding by 5 mm. Hook the heater using the

suspension eyes over the screws, slide it as far as possible to the left and pull the

heater downwards.

 Attach the heater using the materials supplied (see

diagram). Place the bracket on top of the heater with

the short side against the wall. Mark the location of

the hole on the wall and remove the heater. Drill a

hole at the marked spot and insert a plug. Now hang

the heater in place and screw the bracket to the wall,

as shown in the diagram. The heater is now

installed.

Switching on and operation

 Check that the control button is ‘OFF’ (O).

 Fully unwind the electric cable and insert the plug into a suitable 220/240V socket.

 Turn the thermostat dial to + (clockwise as far as possible).

 Switch the heater on by turning the control dial to one of the following three

positions:

Fan only (thermostat always to maximum)

I Heating at half power (1000W)

II Heating at full power (2000W)

The light at the front will turn on.

It is most economical to heat the space at full power, then to switch to half power

to maintain the temperature.

 Both at half and full power, the fan rotates at the same speed; the difference

between the two lies in the number of heating elements in use.

 Once the desired temperature is reached, turn the thermostat dial back slowly until

you hear a click. The temperature is now set. The heater will automatically switch

on and off to maintain the set temperature. When the heater switches off, the pilot

light turns off as well. To set a higher or lower temperature, turn the thermostat dial

either clockwise or anticlockwise.

 To switch the heater off, set the power dial to ‘O’ (off). The pilot light will turn off.

The pilot light, in other words, indicates that the heater is switched on, not that the

heater is connected to the mains!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eurom Sani-Fanheat 2000 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info