Bedienungsanleitung Eurom Siena (Seite 16 von 44) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

474862

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Operating with the buttons:

 Pressing the button switches the atmospheric lighting on. The red light next to the button will be

illuminated. Pressing this button again will switch the atmospheric lighting off. If you press the

button for longer than three seconds, the dimmer function will start to work: the brightness of the light will

gradually increase and then decrease. Release the button when the lighting reaches the desired intensity.

 Pressing the '900W' button sets the heating at half capacity (900 Watt). The red light next to the button will

be illuminated and the ventilator will start to distribute warm air via the upper grille.  This function

only works if the atmospheric screen is working! Pressing this button again will switch the heating off but the

atmospheric lighting will continue to work.

 1800W1800 Watt). The red light next to the button will

be illuminated and the ventilator will start to distribute warm air via the upper grille.  This function

only works if the atmospheric screen is working! Pressing this button again will switch the heating off but the

atmospheric lighting will continue to work.

 Every time you press a button you will hear a 'beep' and this indicates that the fireplace has 'picked up' the

command.

Operating using the remote control:

It takes a little time before the receiver responds to a signal transmitted from the remote control. Do not press a

button more frequently than once per two seconds as this will disrupt the function.

 You switch the atmospheric lighting on and off using the red button on the remote control.

 The black buttons '900W' and '1800W' have the same function as the '900W' and '1800W' buttons on the

fireplace (see above).

 Pressing and holding the black 'dimmer' button increases and decreases the brightness of the light. Release

the button when the lighting reaches the desired intensity.

 Every time you press a button you will hear a 'beep' and this indicates that the fireplace has 'picked up' the

command.

 When you switch a particular function on using the remote control, the red light next to the corresponding

button on the fireplace will be illuminated.

Warning: This heater is not equipped with a device to control the room temperature. Do not use this heater in

small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant

supervision is provided.

Replacing a bulb

 Always unplug the fireplace before replacing a bulb!

 The bulbs get hot during use; allow plenty of time for them to cool down before touching them!

 Two people are required to replace a bulb.

 Carefully remove the glass plate in front of the fireplace by lifting it off its hooks. Put it somewhere safe.

 We advise you to now take the fireplace off the wall. In order to do so, the two screws which attach the

fireplace to the lower spacer bracket must be removed. Lie the fireplace down on a flat, clean surface.

 Under the 'fire' there is a cover place which covers the bulbs. Remove the 5 screws from this cover plate

and remove cover plate.

 You must remove the flexible rotator in order to gain access to the bulbs. Pinch the clamp on the right hand

side and move to the left, away from the rubber. Now slide the rubber off the axle (to the left). Once this is

free of the axle, gently pull forwards and slide/pull gently to the right (out of the left hand side attachment

point).

 Remove the broken bulb and replace with a 40Watt G9 halogen bulb. Never touch a halogen bulb with bare

hands!

 Replace the rotator by following the instructions above in reverse order.

 Screw on the cover plate, hang the fireplace on the wall supports and screw in the screws which attach the

fireplace to the spacer bracket. Finally, replace the glass plate on the hooks, in front of the fireplace.

 The lamp may only be replaced by a person qualified to do so.

Safety feature

The Siena atmospheric fireplace is equipped with a double overheating safeguard.

One overheating safeguard switches the heater off if it overheats internally.This may occur if the heater cannot

give off enough heat or if it cannot draw in enough fresh air. As mentioned above, this is generally caused by

(partially) covering the heater, obstructing the air intake and/or outlet grills or installing the heater too close to a

wall or something similar.

If this happens, turn the fireplace off by switching the main switch to O and remove the plug from the socket.

Leave the fireplace to cool down for at least 15 minutes and remove the cause of overheating. You can then

switch the fireplace back on.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eurom Siena Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info