Bedienungsanleitung Eva Calor Giove (Seite 26 von 55) (Englisch)

668816

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

6.2 First ignition

Before igniting the stove, you MUST have a qualified technician perform "FIRST START-UP" and

calibration. For this purpose, we advise you to contact personnel part of our network of authorised

service centres. The company assumes no responsibility for malfunctions due to improper

installation, failure to install, incorrect first ignition, or improper use.

Make sure that electrical and plumbing connections have been performed properly. Also check

that the hydraulic system (on heating stoves and boilers) has a sufficient expansion tank for

maximum safety. Please note that expansion is calculated considering 6% of the whole volume

contained in the system. Any damage to the system or to equipment will not be considered under

warranty. The presence of the tank fitted on the unit does not guarantee adequate protection

against sustained thermal expansion of the system water.

Fill up the system through a refill valve (to be provided externally to the stove). During recovery,

it is advisable not to exceed a maximum pressure of 1 bar. Pressure can be read directly on the

pressure gauge (item 7 par. 5.5).

The water loading phase should be simultaneous to air exhaust.

Before lighting the stove, also check that the brazier is pushed back towards the rear wall

of the combustion chamber.

The first few times you light the stove, it may give off odours due to the evaporation of paint or

grease. Simply ventilate the room to make the odour go away, avoiding prolonged exposure as

vapours can be harmful to people or animals. Do not allow children to stay in the room during this

first phase.

When the tank is loaded for the first time, the feed screw must fill up for a given period. During this

time, pellets will not be distributed within the combustion chamber. To overcome this difficulty, use

the command "initial load" in menu 7 of the control panel (see further details to follow).

6.3 Ignition and normal operation

Before igniting the stove:

- Check that the furnace door is locked.

- Make sure that the pellet tank is full or contains such enough so that the stove will function for

the desired amount of time.

- Make sure that the brazier is clean, free of ashes, combustion residue or unburned pellets (if

necessary, remove the brazier and thoroughly clean it, then replace it with care in its

housing). In the event or start-up with the programmable thermostat, make sure that the

brazier is in the indicated conditions after last use.

When the stove is connected to the electrical system but not in work mode, the display will show

the message "OFF".

6.3.1 Stove start-up

To start up the stove, hold and press the start button (4) for 2 seconds

If you start the stove during the final cleaning phase, the display may show the message "WAIT

COOLING." In this case, wait for a minute before retrying ignition.

First phase. Preparation

The message "START" will appear on the display. In this phase, which lasts for about one minute,

the pellet glow plug activates and combustion chamber forced ventilation starts along with

activation of the fume extraction fan.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eva Calor Giove Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Eva Calor Giove

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info