Bedienungsanleitung Eva Calor Saturno (Seite 39 von 55) (Englisch)

814224

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

8 SAFETY and ALARMS

8.1

Safety devices

CAUTION: during operation, some parts of the stove (door, handle, ceramic parts) can

reach very high temperatures.

Remember to keep at the previously mentioned safe distance.

Be careful, use caution and always follow the instructions.

If during operations any part of the stove or the exhaust pipe leak smoke, immediately turn off

the stove without removing the power supply and ventilate the room. Then, once cooled down,

verify the reason for the leak and, if necessary, call service personnel.

The stove is equipped with several devices which intervene in order to ensure safe operation.

CAUTION: safety devices are designed to eliminate any risk of damage to persons, animals or

things, and tampering with or servicing by unauthorised personnel could compromise their safety.

Safety devices on the stove include the following:

8.1.1 Fume exhaust pressure sensor

This sensor is connected to the fume exhaust pressure duct. It controls internal pressure to the

duct, monitoring any occlusion of the chimney flue and allowing use of the stove in total safety.

When it activates

If proper operation conditions in the fume exhaust duct are altered (improper installation, the

presence of obstacles or impediments in the exhaust tube, negligent maintenance, adverse

weather conditions such as persistent wind, etc.), the pressure sensor (pressure gauge) stops

electrical power supply to the pellet feed screw, thus blocking pellet feeding to the brazier and

sending an alarm signal to the board.

The alarm can also be caused by clogging in the stove, by improper combustion or lack of annual

stove cleaning.

When the alarm goes off, the display shows the message "AL 8 – LOW PRESSURE”.

What to do

- Put the stove in stand-by by pressing the off button for a few seconds (4). (The acoustic alarm

stops).

- Wait and make sure that the combustion of pellets left in the brazier has been completed.

- Wait for the stove to cool down, then verify and remove the causes which caused the safety

devices to go off. Finally, after having cleaned the brazier, re-start the stove by pressing the

ON/OFF button (4).

In the event of a repeated alarm, call a service centre.

8.1.2 Boiler /structure temperature sensor

The stove is equipped with a manual reset bulb thermostat whose function is to preserve the

boiler, pellet tank and, consequently, the whole structure from excessive temperature changes.

When it activates

For hydro stoves, if the water boiler temperature reaches a threshold of 85°C, while for air stoves,

if the pellet loading tube reaches the threshold of 85°C.

In both situations, the thermostat interrupts electrical power to the feed screw, thus blocking pellet

feeding to the brazier and sending an alarm signal to the board.

The display will show the message “AL 7 – Thermal safety”.

What to do

- Put the stove in stand-by by pressing the off button for a few seconds (4). (The acoustic alarm

stops).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eva Calor Saturno Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Eva Calor Saturno

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info