Bedienungsanleitung Eva Calor Tosca 15 kW (Seite 30 von 55) (Englisch)

668823

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

Ventilation speed is proportional to operating power and cannot be modified independently with

respect to stove power.

In channelled air models, the stove has two rear hot air outputs, one on the right and the other on

the left, under the pellet tank. Each of the two outputs has an independent control menu (see

chapter 7 menu).

6.3.7 Circulator (hydro and boiler models)

Hydro models have a circulator and an expansion tank for direct connection of the system stove

to radiators. The circulator starts as soon as water reaches a temperature of 55° C (value that must

not be lowered to prevent formation of condensation in the stove) and works according to water

temperature, even with the stove off. A bleed screw is available on the back of the stove to remove

any air in the circulator itself.

6.3.8 External thermostat

Stove operation can be adjusted to any external room thermostat connected to the circuit board

(see electrical diagram). The thermostat connection is made using a 2x0.5 mm2 cable. This

operation should be performed by qualified personnel.

The external thermostat works in parallel to the internal thermostat of the stove. To work the

external thermostat exclusively, set room temperature to minimum (7° C). At this point, stove

modulation will be controlled by the external thermostat.

During the working phase, if the room temperature is lower than the set temperature and the

external thermostat is active (closed contact), the stove will operate at the set power level. When

the room temperature reaches the set temperature, (external thermostat contact open), the stove

will go to minimum power and the display will show the message "MODULATE". This modulation

has been completed only if the room temperature returns to being lower than the set temperature

in the external thermostat.

Ambient

sensor

Thermostat

6.3.9 Brazier cleaning

During normal operation in work mode, "BRAZIER CLEANING" is activated at set intervals for a

duration of about 45 seconds. During this time, the display will show the message "BRAZIER

CLEANING", stove ventilation increases and the flame lowers in the brazier. This operation is

necessary to decrease the likelihood of ash accumulation of ash inside the brazier.

If you notice an excessive accumulation of pellets in the brazier (over half the level of the

brazier itself), immediately switch off the stove and clean the brazier. Promptly contact a

service centre.

6.3.10 Shutdown

To turn off the stove, hold button 4 for a few seconds .

Once the shutdown signal has been received, the display will show a "FINAL CLEANING"

message and the fume exhaust fan will continues to run at full speed for a minimum time of about

10 minutes to ensure complete cooling of the stove. The hot air fan will also continue to run until

the stove cools down.

CAUTION: Never disconnect the power supply at this stage, as this may create problems

for the stove and compromise the subsequent phases of ignition.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eva Calor Tosca 15 kW Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Eva Calor Tosca 15 kW

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info