If you select the “STAND-BY” mode, the stove switches off after a period of time, set by Pr44, during which the room temperature remains at a value higher than
the SET temperature.
Only if the following condition occurs it is then possible to switch the stove back on:
TSET < (Tstove-Pr43)
FOR THE INSTALLER:
There are 3 standby modes:
Mode 1
WITH RESPECT TO THE WATER TEMPERATURE ENVIRONMENT PROBE
Having set the water temperature, commence operation of the stove.
1- With the room set reached, the stove goes into stand-by.
2- With the air set not reached, the stove is working.
Approaching the Water Set, the stove goes into modulation and remains in modulation.
It only goes into stand-by when the air set is reached.
It comes back on when the stove falls below the Air Set.
The room probe has priority.
In this case, the pump will shut off to maintain the temperature in the stove.
Mode 2
WITH RESPECT ONLY TO THE WATER TEMPERATURE
Having set the water temperature, commence operation of the stove.
Nearing the Set Water, the stove goes into modulation and when it is passed the Set goes into modulation and then stand-by.
Below Set the stove comes on again and resumes operation.
The stove in no way considers the temperature measured by the ambient sensor of the same stove.
Water takes priority.
Mode 3
WITH RESPECT TO THE THERMOSTAT AND TO THE TEMPERATURE OF THE WATER.
Having set the water temperature, commence operation of the stove.
1- With the thermostat open the stove goes into modulation and then stand-by.
2- With thermostat closed the stove is operational.
Nearing Set Water, the stove goes into modulation and remains in modulation. It only goes into stand by mode when the thermostat opens the contact. It turns
on when the thermostat closes the contact.
The stove in no way considers the temperature measured by the ambient sensor of the same stove.
The thermostat takes priority.
In this case, the pump will shut off to maintain the temperature in the stove
Menu 05 – BUZZER MODE
When "OFF", the acoustic signal is disabled.
Menu 06 – INITIAL LOAD
This function is important if the stove is new or if the stove is off due to the absence of pellets in the hopper.
INITIAL IGNITION MUST BE PERFORMED BY AUTHORISED PERSONNEL ONLY, NOT BY THE PURCHASER.
CONTACT THE ASSISTANCE CENTRE TO ARRANGE TO SEND OUT THE SPECIALIST TECHNICIAN TO YOU.
Use this function to load pellets for a pre-defined period when the stove is switched off and cold. Start with button P1 and stop with button P4. Initial loading is only
enabled if the stove is turned off.
Menu 07 – STOVE STATUS
This function displays the current status of the stove showing the status of all the devices connected to it. A few examples are included in the following pages. The
following will be displayed: status time (including ignition, shutdown, work, etc.), the pellet load and power, the flue gas temperature and the motor rpm, the board
temperature and the water pressure.
Menu 08 – TECHNICAL CALIBRATIONS
Menu for technicians, installers only.
13.3 USER FUNCTIONS
Standard functioning of a control board properly installed on a stove is described below with reference to the functions available to users. The indications listed
below refer to a control board fitted with programmable chrono-thermostat.
Stove ignition
Ensure that there are pellets in the hopper, that the burn pot is correctly positioned and free from any combustion residues and then close the door.
To turn on the stove, press button P4 for a few seconds. The display shows that the stove is on.
Start-up phase
The stove performs all the steps of the start-up phase according to the parameters concerning its levels and times. The display will show the wording ON, as there
is no pellet loading but the exhaust blower is in operation. PELLET LOADING state will occur where the pellets are being loaded into the burn pot. Once the pellets
have started to burn and the fume temperature is increased, the display will show FIRE ON, a transition phase between ignition and operating output.
Ignition fault
If the fume temperature has not reached the minimum permitted value after a predefined time, at a rate of 2°C/min, the stove goes into alarm status.
If there are unburned pellets inside the burn pot, it is necessary to empty the burn put before switching on the stove again. Pellet waste and potential bursting inside
the combustion chamber will thus be avoided. If the pellets have begun to burn but the alarm state persists, wait until all the pellets are burning and then switch on
again. Check that there are pellets inside the hopper.
Stove operational
At the end of the start-up phase, if no problems occurred, the stove enters its normal working mode.
If the temperature of the stove is the same as that set, the pump will come on, in this case at 55°C.
Upon reaching the set temperature of the stove, the stove will move into MODULATION and will work automatically at minimum power level.
Every 8 hours of continuous work, the stove performs automatic shutdown in order to guarantee cleaning of the burn pot and turbulators.
Changing set room temperature
To change the room temperature, simply press the P2 button. The display shows the current SET temperature value.
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Eva Calor Tosca wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
