Bedienungsanleitung Eva Calor TRINITY (Seite 27 von 39) (Englisch)

751942

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

04. PRODUCT USE

Room temperature reaches the set value (SET temperature)

When the set room temperature value is reached, the stove heat output is automatically set to the minimum value. During this phase

the display shows the message "Modula". If room temperature falls below the set value (Set temperature value), the stove will go

back to the "Work" mode and to the previously set heat output (Set heat output). If there is an external thermostat and the room

temperature has been set to t-e, if the thermostat is open it will begin modulation and if closed, it will return to the heat output set.

Stand-by

When enabled in the menu, the Stand-by function allows the stove to be switched off after complying with the following conditions.

It is enabled if, for a certain time, the ambient temperature is higher than the set temperature (Ambient set) plus a pre-set

temperature delta. The display shows "Standby" and then the remaining minutes. At the end of the given time, the message "Wait

for cooling" appears on the display. In this state, the stove has an auger tube closed (auger tube off) and the heat exchanger switches

off. When the fume temperature reaches a given threshold, the stove enters the stand-by mode and scrolls the wording "Stop eco

temp". The auger tube is switched off (auger tube LED off), the heat exchanger is switched off, as is the exhaust blower .

If the room temperature falls below the set temperature (Ambient set) minus the threshold given by the temperature delta, the stove

switches on again.

Stove switch off

Hold P3 button down to switch off the stove. The message "SWITCH OFF" appears on the display. The auger tube motor stops (the

auger tube LED is off) and the exhaust blower speed is pre-set. The fan of the exchanger (exchanger LED on) remains active until the

fume temperature falls below a pre-set value. After a certain time, if the temperature of the fumes is below a given threshold, the

stove switches off, displaying the message "Off".

Wi-Fi

The configuration procedure is as follows:

1. From a device with a Wi-Fi device (computer/tablet/smartphone), it is necessary to connect to the Wi-Fi network

created by the Wi-Fi module. The name of the network to be searched for (SSID) will be similar to “Evastampaggi-

Wifi_000780FFFFFF”. 2. Verify that the Wi-Fi device (computer/tablet/smartphone) has established the actual

connection to the network created by the Wi-Fi module.

3. Open the browser of the device in use (Internet Explorer, Firefox, etc.) and in the address bar

type in the following address: http://192.168.1.1.

4. The main page of the Wi-Fi module will open, showing certain information about its operation.

8. choose the desired language and continue.

9. Select the network to be used from the list to connect the device to the Internet and enter the password of the

selected network.

10. Click the 'Connect' button to connect the module to the Internet.

11. you will see the message: the device is connecting, wait 30 seconds. The green LED of the wi fi connection is flashing.

12. After a few seconds from the Internet connection, the green LED will light up to indicate that the module has

completed the configuration procedure correctly.

13. At this point the product you have purchased is permanently connected to the Internet.

Now open the browser of the device in use and in the address bar type the following address:

http://evastampaggi.efesto.web2app.it/.

The page of the EFESTO Web App will open, click in the "Register" section of the main menu. Once registered, you will

receive a confirmation e-mail in your mailbox.

14. Return to the main page of the EFESTO Web App and access your account by entering the data (e-mail address and

password) previously used during registration. It is now possible to insert a new device by clicking on the "Add stove"

section of the main menu.

During this procedure you will be prompted for:

- ITEM NUMBER and SERIAL NUMBER that you can find on the back of your electronic device (pellet stove, boiler, etc.),

(the ITEM NUMBER corresponds to the MODEL and the SERIAL NUMBER corresponds to the SERIAL on the label on the

back of the device)

- MAC ADDRESS and REGISTRATION CODE that you will find on the back of your Wi-Fi module (see figure below)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eva Calor TRINITY Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info