Bedienungsanleitung EVO 2014 (Seite 14 von 28) (Englisch)

590562

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

p. 14

WARNING: Do not remove or disable the secondary retention device. As its name implies, it serves as a

back-up for a critical adjustment. If the wheel is not secured correctly, the secondary retention device can

reduce the risk of the wheel disengaging from the fork. Removing or disabling the secondary retention device

may also void the warranty.

Secondary retention devices are not a substitute for correctly securing your wheel. Failure to properly secure

the wheel can cause the wheel to wobble or disengage, which could cause you to lose control and fall, resul-

ting in serious injury or death.

2. Wheels with cam action systems

There are currently two types of over-center cam wheel retention mechanisms: the traditional over-center

cam (ﬁg. 8a) and the cam-and-cup system (ﬁg. 8b). Both use an over-center cam action to clamp the bike’s

wheel in place. Your bicycle may have a cam-and-cup front wheel retention system and a traditional rear

wheel cam action system.

a. Adjusting the traditional cam action mechanism (ﬁg. 8a)

The wheel hub is clamped in place by the force of the over-center cam pushing against one dropout and

pulling the tension adjusting nut, by way of the skewer, against the other dropout. The amount of clamping

force is controlled by the tension adjusting nut. Turning the tension adjusting nut clockwise while keeping

the cam lever from rotating increases clamping force; turning it counterclockwise while keeping the cam

    leverfromrotatingreducesclampingforce.Lessthanhalfaturnofthetensionadjustingnutcanmake

the difference between safe clamping force and unsafe clamping force.

WARNING: The full force of the cam action is needed to clamp the wheel securely. Holding the nut with one

hand and turning the lever like a wing nut with the other hand until everything is as tight as you can get it

will not clamp a cam action wheel safely in the dropouts. See also the ﬁrst WARNING in this Section.

b. Adjusting the cam-and-cup mechanism (ﬁg. 8b)

The cam-and-cup system on your front wheel will have been correctly adjusted for your bicycle by your

dealer. Ask your dealer to check the adjustment every six months. Do not use a cam-and-cup front wheel

on any bicycle other than the one for which your dealer adjusted it.

3. Removing and Installing wheels

WARNING: If your bike is equipped with a hub brake such as a rear coaster brake, front or rear drum, band

or roller brake; or if it has an internal gear rear hub, do not attempt to remove the wheel. The removal and

re-installation of most hub brakes and internal gear hubs requires special knowledge. Incorrect removal or

assembly can result in brake or gear failure, which can cause you to lose control and fall.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

EVO 2014 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info