Bedienungsanleitung Exgain E1800 (Seite 18 von 24) (Englisch)

818961

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

5. USE

- 16 -

- Put the mower at the charging station.

IMPORTANT INFORMATION

If user does not select working in AREA 2, he can not

set the robot working in AREA 3.

- Press key or key to scroll to AREA 3 and press key

to select working in AREA 3. “*”comes in front of AREA3.

4. To set the Memory Point.

is to program the mower where to leaveA Memory point

virtual wire and go inner lawn.Each area should have a

Memory point.

- Select START and confirm it by pressing key . Then

the robot starts follow virtual wire walking.

- Press key to set Memory point in AREA 1 when mower

arrives at Memory 1.

Please keep the voltage of mower more than 27V

- It’s best to set the Memory point in the middle of two

corners.

- A better position of Memory point is a 3 meters length

of virtual wire at the beginning or the end of an area.

Press key to set Memory point in AREA 2 when mower

arrives at Memory 2.

Press key to set Memory point in AREA 3 when mower

arrives at Memory 3.

Take Memory 1, Memory 2, Memory 3 as below picture

before setting the memory points.

for example.

- Route the wire around the passage to separate the area.

The virtual wire to and from the edge of passage is 1meter

at least. check the setting as below picture.

- A minimum distance between the to and from virtual wire which

are to make a passage from one area to another one is 50cm.

- Put the robot back to charging station and wait for working.

5.13 Schedule time setting

1. Select AREA and enter it by pressing key .

- Press key or key to set Hour/ Minute.

2. Select SCHEDULE TIME and enter it by pressing key .

4. To set START TIME.

and confirm the settings by pressing key .

Explanation:

- If Set AREA 1 with 000 minute, it means Non-cutting in

3. Select WEEK (MON,TUE,WED,THU,FRI,SAT,

SUN) and enter it by pressing key .

- Select START TIME and enter it by pressing key .

- Press key or key to set how long should the robot

5. To set working time in each area.

and confirm the settings by pressing key

- Select AREA 1 and enter it by pressing key .

The schedule time setting should be used together

with AREA function. P15-5.12 AREA setting.

works in AREA 1,

.10minutes for each scrolling.(From 000 to 500minutes).

6. Set AREA 2 to AREA 6 as Step5.

AREA 1.

- If user doesn’t select working in AREA 2. (See P15-

). Even user has set a working 5.12AREA SETTING

time in AREA 3, robot will not work in AREA 3.

7. Select EXIT to save or select DEL to delete the settings.

5.14 LINE

1. Select AREA and enter it by pressing key .

2. Select LINE and enter it by pressing key .

3. Select which day and confirm the selection by

key .pressing

LINE:every time mower starts,it has to find wire

cutting and follow it back to station first.

IMPORTANT INFORMATION

All settings need about 3 seconds to memorize, so pls

do not turn off the mower immediately after setting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Exgain E1800 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info