Bedienungsanleitung Exquisit CD350-2D (Seite 9 von 36) (Deutsch, Englisch, Holländisch, Französisch)

717723

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

DESCRIPTION OF THE APPLIANCE, BASIC PARTS (see fig. 1)

1 Switch -(ON/OFF); 6 Fan

2 Thermostat knob 7 Shelf

3 Thermostat indicator 8 Cleaner

4 Electricity supply indicator 9 Condenser

5 Interior light block (LED) 10 Compressor

REVIEW OF MECHANICAL CONTROL (see fig. 1)

1 ― On / off switch for interior light. On / off switch for interior light I -(ON) O –(OFF)

2 ― Thermostat knob. The thermostat is off when there is a zero (0) in the thermostat indicator

space. Turning the thermostat knob clockwise the temperature in the compartment lowers.

3 ― Thermostat indicator. Marked with the symbol

4 ― Electricity supply indicator, marked with the symbol

When the appliance is connected to the electricity supply, the green indicator light is

illuminated. WARNING! The fan switches on and continuously operates.

PREPARING THE APPLIANCE FOR OPERATION

It is recommended to prepare the appliance for operation with a helper.

• Remove package. Lift the appliance away from foamed polystyrene base.

If your appliance is fit with screwed handles. Do not rise or push it taking by

handles. Handles may break.

• Therefore take out adhesive tapes from sides and simply lift the appliance up and take out

the board. Strip adhesive tapes off and open the door. Remove the spacer above the door.

• When positioning the appliance in chosen location, it will move more easily into position if you

lift the front a little and incline it backward allowing it to roll on its casters.

• Suitably dispose the packaging material.

• Take two supports from the bag (see fig. 4) and insert them into the guides at the top back

part of the appliance.

POSITIONING

• Place the appliance in a dry, well ventilated room.

WARNING! The appliance should not be operated in an unheated room or

porch. Place the appliance away from heat sources such as kitchen stove/oven,

radiators, or direct sunlight.

WARNING! The appliance must not touch any pipes for heating, gas or

water supply or any other electrical devices.

• Do not cover the ventilation holes at the top of the appliances – it must be a good air circulation

around the appliance. There should be a gap of at least 10 cm between the top of the appliance

body and any furniture that may be above it. If this requirement is not followed, the appliance

consumes more electrical energy and its compressor may overheat.

• If the appliance is placed in a corner, a gap of at least 1 cm must be left between the appliance

body and the wall (see fig. 2).

• The appliance must stand on a level surface and must not touch the wall. If necessary, regulate

the height of the appliance by adjusting the levelling feet: by turning them clockwise – the front

of the appliance rises, by turning them counter clockwise – it comes down. If the appliance is

tilted slightly backward – the doors will close by themselves.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Exquisit CD350-2D Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info