Bedienungsanleitung Exquisit EKC 301-5 (Seite 24 von 40) (Deutsch, Englisch, Französisch)

720067

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

INSTALLATION INSTRUCTIONS

The installation comes under the exclusive responsibility of specialists.

The installer is held to respect the legislation and the standards enforce in his home country.

How to stick the gasket:

The gasket supplied with the hob avoids all infiltration of liquids in the cabinet.

The gasket supplied with the appliance also allows to maintain in position the appliance, it is not

necessary to use another fixation system.

His installation has to be done carefully, in conformity of the following drawing.

Fitting - installing:

• The cut out sizes are:

Reference Cut-size

EKC301-5 480 x 275 mm

• Ensure that there is a distance of 50 mm between the hob and the wall or sides.

• The hobs are classified as “Y” class for heat protection. Ideally the hob should be installed

with plenty of space on either side. There may be a wall at the rear and tall units or a wall at

one side. On the other side, however, no unit or divider must stand higher than the

hob.

• The piece of furniture or the support in which the hob is to be fitted, as well as the edges of

furniture, the laminate coatings and the glue used to fix them, must be able to resist

temperatures of up to 100 °C.

• The mural rods of edge must be heat-resisting.

• Not to install the hob to the top of a not ventilated oven or a dishwasher.

• To guarantee under the bottom of the hob casing a space of 20 mm to ensure a good air

circulation of the electronic device.

• If a drawer is placed under the work, avoid to put into this drawer flammable objects (for

example: sprays) or not heat-resistant objects.

• Materials which are often used to make worktops expand on contact with water. To protect

the cut out edge, apply a coat of varnish or special sealant. Particular care must be given to

applying the adhesive joint supplied with the hob to prevent any leakage into the supporting

furniture. This gasket guaranties a correct seal when used in conjunction with smooth work

top surfaces.

• The safety gap between the hob and the cooker hood placed above must respect the

indications of the hood manufacturer. In case of absence of instructions respect a distance

minimum of 760 mm.

• The connection cord should be subjected, after building, with no mechanical constraint,

such for example of the fact of the drawer.

• WARNING: Use only hob guards designed by the manufacturer of the cooking appliance or

indicated by the manufacturer of the appliance in the instructions for use as suitable or hob

guards incorporated in the appliance. The use of inappropriate guards can cause accidents.

Stick the gasket (2) two millimeters

from the external edge of the glass,

after removing the protection sheet (3).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Exquisit EKC 301-5 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info