Bedienungsanleitung Exsilent QLeaf Go (Seite 5 von 9) (Englisch)

515478

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

8 9

without soft tip around it) between your

ngers and pull it out of the soft tip.

Placing Qleaf Go in the ear

I Put the end of the soft tip with the

dome(s) loosely in the ear. The pull cord is

situated behind the tragus, directing

towards the nose.

II Insert the device into the ear by pressing on

the at side of the device. Now gently push

the device deeper into the ear. If the mouth

is opened wide, insertion will be easier.

Ideally, the outside of the module (the part of

the module which is not covered by the soft

tip) will be positioned at the entry of the ear

canal after insertion. In this way, the device is

practically invisible and the sound optimal.

There are cases where the ear canal is too

small. In that case, it is possible for the device

to protrude a few millimeters.

If the pull cord protrudes after the insertion of

the device, after which it becomes visible, it

can be easily custom-cut with a side cutter or a

pair of scissors. We recommend, however, that

you leave 2 ribs for easy removal from the ear.

Removing Qleaf Go from the ear

Hold the pull cord rmly and pull it – always

slowly - out of the ear.

Switching between programs

The Qleaf Go is set up with four programs. The

programs can be selected using the AirTAP™

function. To change between the programs,

the Qleaf Go wearer taps the ear gently with

the hand. The tap generates an air pressure

change that is detected by the Qleaf Go to

change the program. After the insertion of the

battery, the device is set by default to program

one. Gently tapping on the ear will produce

two beeps, indicating a switch from program

one to program two. After another gentle tap,

In the box

A Qleaf Go module

B Qleaf Go soft tip package

C Battery

D Battery ejection tool

E Carrying box

F Qleaf Go User manual

Placing the battery

While using a new battery: rst remove the

sticker from the + pole. Hold the module and

insert the battery as indicated.

Eject the battery

Hold the module and eject the battery with the

battery ejection tool.

If the module is placed in the soft tip, you can choose

to leave the soft tip partially on the device and only

‘peel o’ until you can easily access the battery

opening to eject the battery (see image 5, p. 5).

Inserting Qleaf Go in the

soft tip

I Insert the module into the soft tip with the

CE mark rst and visible.

II Next, simultaneously push the Qleaf Go

device with the thumb in the soft tip and

pull the pull cord.

III Please make sure that the module is

inserted all the way into the soft tip.

Make sure your hands are clean while inserting

the Qleaf Go. Make-up, cream, body oil, gel,

hairspray and likewise products can contaminate

the module and can, for example, contribute to

the clogging of the microphone opening.

Removing Qleaf Go from the

soft tip

I Pull the pull cord to the front of the

Qleaf Go and ‘peel’ the soft tip from the

module as far as possible.

II Place the Qleaf Go device (the part

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Exsilent QLeaf Go Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info