Bedienungsanleitung Extraflame Comfort P70 H49 (Seite 20 von 36) (Englisch)

696308

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

1 2

OFF

22.5°C 14:10

ENGLISH

OPERATION AND LOGIC

IGNITION

Once the points listed previously have been checked, press key 1 for three seconds to ignite the stove. 15 minutes are given for the ignition

stage, after ignition and once the control temperature has been reached, the stove interrupts the ignition phase and switches to the START-UP

mode.

STARTING

During the start-up stage, the stove stabilises combustion, increasing it gradually, to then start ventilation and switch to the WORK mode.

WORK

During the work stage, the stove reaches the set power and works to reach the set room temperature. See following item.

SET THERMOSTAT ADJUSTMENT

The room temperature setting can be set using buttons 4 and 5, from Low-07 to 40°C -Hot

LOW  HOT

If the temperature setting is on “Low” (set below the 7°C threshold) the stove will always function at minimum.

If the setting is on “Hot” (set above the 40°C threshold) the stove will not modulate, always functioning and only at the set power.

SET POWER ADJUSTING

The power setting features 5 operating levels, via button 5, (access) 1 and 2 ( adjustment).

Power 1 = minimum level - Power 5 = maximum level.

WORK WITH ROOM PROBE STANDARD

The appliance controls the room temperature via a probe tted on the appliance.

Once the the set temperature has been reached, it will automatically go to minimum or switch o activating the Stand by function, reducing

pellet consumption to a minimum.

By default the STBY function is always set on OFF (light

on).

For its activation and logic, follow the indications on the next page, chapter: Stand by.

BURN POT CLEANING

During the work stage, the stove has an internal counter which cleans the burn pot after a set amount of time.

This stage will be shown on the display, it will bring the stove to a lower power level and will increase the fumes motor for a programmed

amount of time.

When the cleaning stage is nished, the stove will continue its work, going back to the selected power level.

SWITCHOFF

Press key 1 for three seconds.

When the operation has been performed, the appliance automatically enters the switch- o phase, blocking the supply of pellets.

The fumes motor and the hot air ventilation motor will remain on until the temperature of the stove has dropped below the factory

parameters.

REIGNITION

The stove can only be re-ignited if the ue gas temperature has lowered and the preset timer has been reset to zero.

DO NOT USE ANY INFLAMMABLE LIQUIDS FOR IGNITION!

DO NOT ALLOW THE BAG OF PELLETS TO COME INTO CONTACT WITH THE BOILING HOT STOVE DURING THE FILLING

PHASE!

IN THE EVENT OF CONTINUOUS NO IGNITION, CONTACT AN AUTHORISED TECHNICIAN.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Extraflame Comfort P70 H49 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Extraflame Comfort P70 H49

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info