Bedienungsanleitung Extraflame Duchessa Idro Steel (Seite 20 von 32) (Englisch)

751933

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

ENGLISH

LOW

The following menu allows the user to adjust the percentage of pellet feed.

If the stove has functioning problems owing to the quantity of pellets, adjust pellet feeding directly from the control board.

The problems correlated to the amount of fuel can be divided into 2 categories:

NO FUEL:

� the stove is never able to develop a suitable ame, tending to remain very low even at high power.

� at minimum power the stove tends to almost switch-o putting the stove in ““NO PELLETS” alarm conditions.

� when the stove displays the “NO PELLETS” alarm, there may be non-burned pellets inside the burn pot.

EXCESS FUEL:

� the stove develops a very high ame even at low power.

� the panoramic glass is very dirty, obscuring it almost totally.

� the burn pot tends to become encrusted, blocking the holes for air intake due to excessive pellet loading, as it is only burned partially.

The adjustment to be performed is in percentages. Therefore changing this parameter will lead to a proportional variation of all stove

feeding speeds. Feeding is from -30% to +20%.

RESET

Allows the user to reset all values modiable by the user to the default values.

CONTROLS PROCEDURE

� Press key 6.

� Proceed by pressing key 2 until USER MENU is displayed.

� Conrm using key 6.

� Press key 2 until RESET is displayed.

� Press keys 4-5 to select ON and press key 6.

� ''DONE'' will appear on the display to conrm.

CONTROLS PROCEDURE

� Press key 6.

� Proceed by pressing key 2 untilUSER MENU is displayed.

� Conrm using key 6.

� Press key 2 until "PELLET" is displayed.

� Use keys 4 - increase 5 to(4) or decrease (5) the load during the WORK stage.

� Press key 1 several times to conrm and exit the menu.

SET CHRONO

This stage is used to program when the generator automatically turns on and o.

The factory setting for SET CRONO is disabled on the generator.

The chrono allows the user to program 4 time spans within a day to use every day of the week.

The switch-on and switch-o time can be set in every time slot, along with the days of use of the programmed time slot and the

desired water temperature (65 - 80°C).

The setting of the current day and time is essential to ensure the chrono operates correctly.

RECOMMENDATIONS

Before using the chrono function, set the current day and time. Therefore check that the points listed in the “Set clock” sub-chapter have been

followed, so that the chrono function works. Aside from programming it, activate it as well.

The ignition and switch-o times must be within the arc of one day, from 0 to 24 and not over several days:

CORRECT INCORRECT

Switch-on time 07:00

Switch-o time 18:00

Switch-on time 22:00

Switch-o time 05:00

Example:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Extraflame Duchessa Idro Steel Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Extraflame Duchessa Idro Steel

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info