Bedienungsanleitung Extraflame Giusy (Seite 17 von 36) (Englisch)

643370

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

17ENGLISH

FUNCTIONING AND LOGIC

IGNITION

Once the points listed previously have been checked, press key 1 for three seconds to ignite the stove. 15 minutes are given for the ignition

stage, after ignition and once the control temperature has been reached,

the stove interrupts the ignition phase and switches to the STARTING mode.

STARTING

During the start-up stage, the stove stabilises combustion, increasing it gradually, to then start ventilation and switch to the WORK mode.

WORK

During the work stage, the stove reaches the set power and works to reach the set room temperature. See following item

SET THERMOSTAT ADJUSTMENT

The room temperature setting can be set using buttons 2 and 3, from low-07 to 40°C -hot

LOW  HOT

if the temperature setting is on “low” (set below the 7°C threshold) the stove will always function at minimum.

If the setting is on “hot” (set above the 40°C threshold) the stove will not modulate, always functioning and only at the set power.

SET POWER ADJUSTMENT

Set the functioning power from 1 to 5 (settable using keys 4 - 5).

Power 1 = minimum level - Power 5 = maximum level.

WORK WITH ROOM PROBE STANDARD

The appliance controls the room temperature via a probe tted on the appliance.

Once the the set temperature has been reached, it will automatically go to minimum or switch o activating the Stand by function, reducing

pellet consumption to a minimum.

By default the STBY function is always set on OFF (light

on).

For its activation and logic, follow the indications on the next page, Chapter: Stand by.

BURN POT CLEANING

During the work stage, the stove has an internal counter which cleans the burn pot after a set amount of time.

This stage will be shown on the display, it will bring the stove to a lower power level and will increase the fumes motor for a programmed

amount of time.

when the cleaning stage is nished, the stove will continue its work, going back to the selected power level.

SWITCHOFF

Press key 1 for three seconds.

when the operation has been performed, the appliance automatically enters the switch- o phase, blocking the supply of pellets.

The fumes motor and the hot air ventilation motor will remain on until the temperature of the stove has dropped below the factory

parameters.

REIGNITION

The stove can only be re-ignited if the ue gas temperature has lowered and the preset timer has been reset to zero.

CLEAN CHECK UP 1  2

IF THE ALARM "CLEAN CHECK UP" ALARM IS PRESENT, IT IS NECESSARY TO MAKE

SURE THAT THE BOTTOM OF THE BURNING POT IS FREE FROM RESIDUES OR DIRT.

THE HOLES IN THE BOTTOM MUST BE COMPLETELY FREE, TO ENSURE CORRECT

COMBUSTION.

IT IS POSSIBLE TO USE THE "EASY SETUP" FUNCTION TO ADJUST THE COMBUSTION

DEPENDING ON THE REQUIREMENTS DESCRIBED. IF THE ALARM SIGNAL PERSISTS,

AND THE ABOVE MENTIONED CONDITIONS HAVE BEEN CHECKED, CONTACT

CUSTOMER SERVICE.

BOTTOM OF BURNING POT

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Extraflame Giusy Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Extraflame Giusy

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info