Bedienungsanleitung Extraflame Giusy (Seite 18 von 36) (Englisch)

643370

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

18 ENGLISH

STANDBY

The STBY function is used if immediate stove switch-o is required when the set temperature has been

reached.

The STBY function can be set at ON or OFF using the procedure described further on.

In the factory the STBY function is always set at OFF (indicator o)

STBY FUNCTION SET AT ON

If the STBY function is active (ON), when the stove reaches the set room temperature and exceeds it by 2°C, it will switch o after a default

delay time, displaying STAND  BY.

When the room temperature is 2°C lower than the setting, the stove will start to work again at the power set on the display, displaying

WORK.

STBY FUNCTION SET AT OFF DEFAULT SETTING

If the stby function is not active (OFF), if the stove reaches the set room temperature, it will go to minimum, modulating and displaying

MODULATION. When the room temperature is below the setting, it will start to work again at the set power, displaying WORK.

CONTROLS PROCEDURE

 press key 5 for a few seconds, until SET CLOCK appears.

 Press key 3 until "USER" appears.

 Press key 5 twice.

 Use key 2 or 3 "ON" to activate or "OFF" to de-activaate.

 Press key 1 several times to conrm and exit the menu.

N.B.: If these calibrations do not solve the problem, please contact your local customer service centre.

CONTROL PROCEDURE

 Press the key 5 for a few seconds; the message SET CLOCK will appear on display.

 Press the key 3 for several times to open the EASY SETUP page.

 Press the key 5 to conrm.

 Use the keys 2 and 3 to increase (3) or decrease (2) the value.

 Press the key 1 for several times to conrm and exit the menu.

EASY SETUP

The volumetric weight of the pellet is the ratio between the weight and the volume of the pellet. This ratio can change while maintaining

the quality of the pellet. By using the EASY SETUP function, it is possible to change the calibration of the volumetric weight, increasing or

decreasing the pre-set values.

In the stove program, the values available go from “– 3”to “+ 3”; all the stoves are calibrated at the factory to the optimal value 0

If you notice an excessive deposit on the burner pot, enter the EASY SETUP program and lower the value by one unit to “- 1”; then wait for the

following day and if there is no improvement, lower the value again up to a maximum of “- 3”. Instead, should it be necessary to increase the

calibration of the volumetric weight of the pellet, it is advisable to go from the default value “0” to “+ 1, + 2, + 3” as required.

EXCESSIVE DEPOSIT OF PELLETS IN THE BURNING

POT

NORMAL OPERATION LITTLE DEPOSIT OF PELLETS IN THE BURNING POT

-3 -2 -1 0 +1 +2 +3

THIRD

DECREASING

RANGE IF THE

FIRST TWO ARE

NOT ENOUGH

SECOND

DECREASING

RANGE IF THE

FIRST IS NOT

ENOUGH

FIRST

DECREASING

RANGE (TEST FOR

1 DAY )

OPTIMAL DEFAULT

VALUE

FIRST

INCREASING

RANGE

SECOND

INCREASING

RANGE IF THE

FIRST IS NOT

ENOUGH

THIRD

INCREASING

RANGE IF THE

FIRST TWO ARE

NOT ENOUGH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Extraflame Giusy Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Extraflame Giusy

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info