Bedienungsanleitung Extraflame Liliana Idro (Seite 18 von 32) (Englisch)

695866

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

18 ENGLISH

OPERATION AND LOGIC

NO IGNITION

FIRST IGNITION COULD EVEN FAIL AS THE AUGER IS EMPTY AND IS NOT ALWAYS ABLE TO LOAD THE BURN POT

WITH THE REQUIRED AMOUNT OF PELLETS ON TIME TO REGULARLY START THE FLAME.

IF THE PROBLEM OCCURS AFTER ONLY A FEW MONTHS WORKING, CHECK THAT ROUTINE CLEANING STATED IN

THE STOVE BOOKLET, HAS BEEN CARRIED OUT CORRECTLY.

IGNITION

Once the points listed previously have been checked, press key 1 for three seconds to ignite the stove.

15 minutes are available for the ignition phase. After ignition and having reached the control temperature, the stove interrupts the ignition

phase and passes to STARTING.

STARTING

During the start-up phase, the stove stabilises combustion, increasing it progressively, to then start ventilation and pass on to WORK.

WORK

During the work phase, the stove reaches the set power; see following item.

SET POWER ADJUSTMENT

Set the operating power (from 1 to 5) .

Power 1 = minimum level - Power 5 = maximum level.

SET H2O TEMPERATURE ADJUSTMENT

Set the boiler temperature between 65 - 80°C .

PUMP OPERATION

The pump activates water circulation when the temperature of the water inside the stove reaches 60°C. As the pump always functions above

60°, an always open heating area is recommended to make product functioning homogenous, preventing overheating blocks. Normally this

area is dened “Safety zone”.

BURN POT CLEANING

At pre-set intervals the stove performs burn pot cleaning, switching the machine o.

When the cleaning phase is nished, the stove will re-start automatically and continue its work going back to the power level selected.

MODULATION and HOFF

As the water temperature approaches the set point, the boiler starts to modulate automatically bringing itself to the minimum power.

If the temperature increases beyond the set point, it will automatically switch o indicating HOFF and will automatically go back on when

the temperature drops below the set point.

SWITCHOFF

Press key 1 for three seconds.

When the operation has been performed, the appliance automatically enters the switch-o phase, blocking the supply of pellets.

The ue gas exhaust motor will remain on until the stove temperature has dropped below the factory parameters.

REIGNITION

The stove can only be re-ignited automatically or manually when the cooling cycle conditions and the preset timer have been satised.

DO NOT USE ANY INFLAMMABLE LIQUIDS FOR IGNITION!

DO NOT ALLOW THE BAG OF PELLETS TO COME INTO CONTACT WITH THE BOILING HOT STOVE DURING THE FILLING PHASE!

IN THE EVENT OF CONTINUOUS NO IGNITION, CONTACT AN AUTHORISED TECHNICIAN.

IT IS FORBIDDEN TO USE THE APPLIANCE WITHOUT THE DIVIDER AND/

OR GLASS PROTECTION SEE THE FIGURE TO THE SIDE. ITS REMOVAL

JEOPARDISES THE SAFETY OF THE PRODUCT AND IMMEDIATELY VOIDS THE

WARRANTY PERIOD. IN THE CASE OF WEAR OR DETERIORATION REQUEST

AFTERSALES ASSISTANCE FOR REPLACEMENT OF THE PART REPLACEMENT

THAT IS NOT UNDER GUARANTEE AS THE COMPONENT IS SUBJECT TO WEAR.

BURN POT UPPER DIVIDER

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Extraflame Liliana Idro Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Extraflame Liliana Idro

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info