Bedienungsanleitung Extraflame LP20 (Seite 27 von 40) (Englisch)

811772

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

OFF

OPERATION AND LOGIC

IGNITION

Once the points listed previously have been checked, press key 1 for three seconds to ignite the stove.

15 minutes are available for the ignition phase. After ignition and having reached the control temperature, the stove interrupts

the ignition phase and passes to STARTING.

STARTING

During the starting phase, the stove stabilises combustion, increasing it progressively, to then start ventilation and pass on to

WORK.

WORK

During the work phase, the stove reaches the set power; see following item.

ADJUSTING THE POWER SETTING

Set the functioning power from 1 to 5 (settable using keys 2 - 3).

Power 1 = minimum level - Power 5 = maximum level.

H2O TEMPERATURE SET ADJUSTMENT

Set the boiler temperature from 65 - 80°C (settable using keys 4 - 5).

PUMP OPERATION

The pump activates water circulation when the temperature of the water inside the stove reaches approx. 60°C. As the pump

always functions above 60°, an always-open heating area is recommended to make product functioning homogenous, avoiding

overheating blocks. Normally this area is dened “Safety zone”.

ENVIRONMENTAL TEMPERATURE in the models envisioned)

The front ventilation can be activated/deactivated and the room temperature controlled by means of the room probe (as per

standard). (See the "enable fan" chapter on the following pages.)

BURN POT CLEANING

While working, the stove has an internal counter which cleans the burn pot after a set amount of time.

This phase will be shown on the display, it will bring the stove to a lower power level and will increase the ue gas motor for a

programmed amount of time. When the cleaning phase is nished, the stove will continue work going back to the selected power

level.

MODULATION and H-OFF

As the water temperature approaches the set point, the boiler starts to modulate automatically bringing itself to the minimum

power.

If the temperature increases beyond the set point, it will automatically switch o indicating HOFF and will automatically go

back on when the temperature drops below the set point.

SWITCHOFF

Press key 1 for three seconds.

When the operation has been performed, the appliance automatically enters the switch- o phase, blocking the supply of pellets.

The ue exhaust motor and the hot air ventilation motor will remain on until the temperature of the stove has dropped

below the factory parameters.

REIGNITION

The stove can only be re-ignited automatically or manually when the cooling cycle conditions and the preset timer have been

satised.

| ENGLISH

NO IGNITION

FIRST IGNITION COULD EVEN FAIL AS THE AUGER IS EMPTY AND IS NOT ALWAYS ABLE TO LOAD THE BURN POT

WITH THE REQUIRED AMOUNT OF PELLETS ON TIME TO REGULARLY START THE FLAME.

IF THE PROBLEM OCCURS AFTER ONLY A FEW MONTHS WORKING, CHECK THAT ROUTINE CLEANING STATED IN THE

STOVE BOOKLET, HAS BEEN CARRIED OUT CORRECTLY.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Extraflame LP20 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Extraflame LP20

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info