Bedienungsanleitung Extraflame Lucia (Seite 8 von 36) (Englisch)

695853

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

8 ENGLISH

INSTALLING INSERTS

When installing inserts, access must be prevented to the internal parts of the appliance and it must not be possible to access live parts during

extraction operations.

Any wiring, for example the power cable or room probe, must be positioned so as not to be damaged during movement of the insert and must

not come into contact with hot parts. If a cavity made of combustible material is installed, we recommend taking all the safety precautions

indicated by the installation standards.

VENTILATION AND AERATION OF INSTALLATION ROOMS

Ventilation in the event of a non-hermetic generator and/or of non-sealed installation must take place respecting the minimum area indicated below:

Appliance categories Reference standard

Percentage of the

net opening section with respect to the

appliance fumes outlet section

Minimum net opening value of the

ventilation duct

Pellet stoves UNI EN 14785 - 80 cm²

Boilers UNI EN 303-5 50% 100 cm²

INSTALLATION

GENERAL

The ue gas exhaust and hydraulic connections must be carried out by qualied personnel who must issue installation conformity

documentation compliant with national standards.

The installer must provide the owner or person acting for him, according to the legislation in force, with the declaration of conformity,

supplied with:

1) the use and maintenance manual of the appliance and of the system components (such as for example, the smoke ducts, chimney, etc.);

2) photocopy or photograph of the chimney plaque;

3) system booklet (where applicable).

The installer must ask to be issued with a receipt stating that the documentation has been provided, and must keep it with a copy of the technical

documentation relating to the installation.

For installation in a condominium, prior approval from the condominium's administrator must be requested.

Where required, check the exhaust gas emissions after installation. Should a sampling point be installed, it must be airtight.

COMPATIBILITY

Do not install in rooms with a re hazard. It is also forbidden to install it in living areas with the following characteristics:

1. where there are liquid fuel appliances with continuous or discontinuous operation that draw the combustion air into the room in which they

are installed.

2. where there are type B gas appliances intended for heating, with or without domestic hot water production and in adjacent and communicating

rooms.

3. where the depression measured in situ between the external and internal environment is greater than 4 Pa.

N.B.: Watertight appliances can also be installed in the cases indicated in points 1, 2 and 3 of this paragraph.

INSTALLATIONS IN BATHROOMS, BEDROOMS AND STUDIO FLATS

Installation in bathrooms, bedrooms and studio ats is only allowed for sealed or closed hearth appliances with ducted combustion air taken

from the outside.

oor protection

POSITIONING AND SAFETY DISTANCES

The support surfaces and/or points must have a suitable capacity to bear the overall weight

of the appliance, accessories and coverings. If the oor is made of a combustible material,

we recommend using a non-combustible material to protect the front part from any burnt

material which might fall during routine cleaning operations. The generator must be level

to function properly. The side walls, the rear walls and the oor support surface should be

made of non-combustible material.

One must also bear in mind all laws and national,

regional, provincial and town council regulations in force

in the country in which the appliance has been installed,

as well as the instructions contained in this manual.

Air inlet

Under any condition, including in the presence of extractor hoods and/or of controlled forced ventilation systems, the pressure dierence

between the generator installation rooms and the outside must always be equal to or less than 4 Pa.

MINIMUM DISTANCES

Installation next to ammable or heat-sensitive materials is permitted only if the special

safety distances specied on the label at the beginning of the manual (pag.2) are

observed. If the materials are not ammable, you must keep a side and rear distance of at

least 100 mm (without the inserts). For products equipped with rear spacers, wall-mounting

installation is permitted exclusively for the rear side.

PREPARATIONS FOR MAINTENANCE

To carry out extraordinary maintenance operations on the product, it may be necessary to move it away from the adjacent walls. This must be

done by a technician authorised to disconnect the combustion product evacuation ducts and then reconnect them. For heaters connected to the

hydraulic system, the connection between the system itself and the product must be made in such a way that, when an authorised technician is

about to carry out extraordinary maintenance operations, it is possible to move the heater at least 1 metre away from the adjacent walls.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Extraflame Lucia Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Extraflame Lucia

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info