Bedienungsanleitung Extraflame Lucia (Seite 23 von 36) (Englisch)

695853

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

23ENGLISH

SETTINGS

• DATETIME

• LANGUAGE

• DEGREES

See chapter: SettingS for firSt uSe

DISPLAY

This menu allows you to adjust the brightness of the display. The possible values go from OFF, 1 to 20. If OFF, the display backlight is at the

maximum intensity and goes out after a 60 second delay.

The backlight comes back on when a key is pressed or if an alarm is generated.

CONTROLS PROCEDURE

 Press 6.

 Press 3 until SETTINGS appears and conrm by pressing 6.

 Keep pressing 3 until DISPLAY appears and conrm by pressing 6.

 Use keys 4 -5 to set the desired intensity.

 Press 6 to conrm or 1 to return to the previous menus to the initial state.

STAND  BY

If enabled, the STANDBY function is used to switch o the machine from the additional thermostat

CONTROLS PROCEDURE

 Press 6.

 Press 3 until SETTINGS appears and conrm by pressing 6.

 Keep pressing 3 until STANDBY appears and conrm by pressing 6.

 Use keys 4-5 to enable (ON) / disable (OFF).

 Press 6 to conrm or 1 to return to the previous menus to the initial state.

FOR CORRECT OPERATION, SET THE SET THERMOSTAT TO LOWTA.

> SEE CHAPTER ON THE ADDITIONAL THERMOSTAT SETTINGS

STANDBY FUNCTION ON

If the STAND-BY function is active (ON), if the room temperature exceeds the value of the SET THERMOSTAT + DELTA T OFF, then the stove

will switch o after a preset delay, displaying STANDBY.

When the room temperature is lower than the SET THERMOSTAT - DELTA T and after a possible cooling time, the stove switches back on.

STANDBY FUNCTION OFF FACTORY SETTING

If the STAND-BY function is not active (OFF ), if the stove exceeds the set room temperature it will switch to the minimum value, modulating

and displaying MODULATION. When the room temperature is lower than the SET THERMOSTAT the stove goes back to operating at the set

power, displaying WORK.

OPERATION WITH ADDITIONAL THERMOSTAT OPTIONAL

STANDBY FUNCTION OFF FACTORY SETTING

If the STAND-BY function is not active (OFF ), if the stove exceeds the room temperature set on the additional thermostat (contact open) it will

switch to the minimum value, displaying MODULATION. When the room temperature is lower than the value set on the additional thermostat

(contact closed), the stove goes back to operating at the set power, displaying WORK.

STANDBY FUNCTION ON

When the STAND-BY function is active (ON), when the room temperature set on the additional thermostat has been reached (contact open),

the stove will switch o after a preset delay, displaying STANDBY.

When the room temperature is lower than the value set on the additional thermostat (contact closed) and after a possible cooling time, the

stove switches back on.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Extraflame Lucia Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Extraflame Lucia

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info