Bedienungsanleitung Extraflame MARINA IDRO H11 (Seite 24 von 40) (Englisch)

811775

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

24 ENGLISH

EASY SETUP

The volumetric weight of the pellet is the ratio between the weight and the volume of the pellet. This ratio may change while keeping the

quality of the pellet unchanged. By using the EASY SETUP function, it is possible to change the calibration of the volumetric weight by

increasing or decreasing the pre-set values.

In the stove program, the available values go from “– 3” to “+ 3”; all stoves are calibrated during production with the optimal value which is 0.

If you notice an excessive deposit on the burning pot, access the EASY SETUP program and lower the value to “- 1”; then wait until the next

day and if there is no improvement, decrease again, to a maximum of “- 3”.

Instead, if it is necessary to increase the calibration of the volumetric weight of the pellet, go from the factory value “0” to “+ 1, + 2, + 3” as

required.

EXCESSIVE PELLET DEPOSIT IN THE BURN POT NORMAL OPERATION MINIMUM PELLET DEPOSIT IN THE BURN POT

-3 -2 -1 0 +1 +2 +3

THIRD

DECREASE

RANGE IF THE

FIRST TWO ARE

NOT ENOUGH

SECOND

DECREASE

RANGE IF THE

FIRST IS NOT

ENOUGH

FIRST DECREASE

RANGE (TEST

FOR 1 DAY)

OPTIMAL FACTORY

VALUE

FIRST INCREASE

RANGE

SECOND

INCREASE

RANGE IF THE

FIRST IS NOT

ENOUGH

THIRD INCREASE

RANGE IF THE

FIRST TWO ARE

NOT ENOUGH

CONTROLS PROCEDURE

Press key 6.

Press key 3 until EASY SETUP appears and conrm by pressing key 6.

Use keys 4 and 5 to set the range.

Press key 6 to conrm and key 1 to return to the previous menus to the initial state.

N.B.: IF THIS CALIBRATION DOES NOT SOLVE THE PELLET DEPOSIT IN THE BURN POT, PLEASE CONTACT YOUR LOCAL AFTER

SALES CENTRE.

VENTILATION

The menu allows you to enable and adjust the speed (-2, -1, 0, +1, +2) of the front fan.

ENABLING CONTROLS PROCEDURE

Press key 6.

Press 3 until VENTILATION appears and conrm by pressing 6.

Conrm ENABLING by pressing the 6 key.

Use keys 4 -5 to enable (ON) or disable (OFF) and conrm by pressing 6.

Press 1 to return to the previous menus to the initial state.

SPEED CONTROLS PROCEDURE

Press key 6.

Press 3 until VENTILATION appears and conrm by pressing 6.

Keep pressing 3 until SPEED appears and conrm by pressing 6.

Use keys 4 -5 to adjust the speed (-2, -1, 0, +1, +2) and conrm by pressing 6.

Press 1 to return to the previous menus to the initial state.

SET THERMOSTAT controls procedure

Press key 6.

Press 3 until VENTILATION appears and conrm by pressing key 6.

Keep pressing 3 until SET THERMOSTAT appears and conrm by pressing 6.

Use keys 4 5 to adjust the room temperature (7°C - 37°C) and conrm by pressing 6.

Press 1 to return to the previous menus to the initial state.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Extraflame MARINA IDRO H11 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Extraflame MARINA IDRO H11

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info