Bedienungsanleitung Extraflame Mietta (Seite 24 von 40) (Englisch)

695849

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

ENGLISH

OPERATION AND LOGIC

IGNITION

Once the previously listed points have been checked, press key

for three seconds to ignite the stove.

15 minutes are available for the ignition phase. After ignition and after reaching the control temperature, the

stove interrupts the ignition phase and switches to PREPARATION.

PREPARATION

During the preparation phase, the stove stabilises combustion, increasing it progressively, to then start ventilation and switch to WORK.

WORK

During the work phase, the stove will function at the set power and work to reach the set room temperature. See next heading.

REGULATION OF SET THERMOSTAT

When the key

is pressed, the set temperature is viewed; it can be changed using keys

from LOWTA 07°C to 40°C - HOT.

The change must be confirmed by pressing the key

LOWTA  HOT

If the temperature is set at “LOWTA” (set below the limit of 7°C), the stove will always run at minimum.

If the setting is on “HOT” (set above the limit of 40°C) the stove will not modulate, running only and always at the set power.

REGULATION OF SET POWER

The set power has 5 operating levels, When key

is pressed, the set power is displayed; it can be changed using keys

Power 1 = minimum level - Power 5 = maximum level.

The change must be confirmed by pressing the key .

To set power 1 it is necessary to press and hold the key

for 3 seconds.

WORKING WITH ROOM SENSOR STANDARD

The appliance monitors the room temperature using a sensor incorporated into the handheld.

Once the set temperature has been reached, it will automatically switch to the minimum power level or turn o, activating the STANDBY,

function, reducing pellet consumption to a minimum.

By factory default, the STANDBY function is always set to OFF.

For information on its activation and logic, follow the instructions on the next page, chapter: STANDBY.

BURN POT CLEANING

During the working phase, the stove has an internal timer, which after a pre-set period of time cleans the burn pot.

This phase is shown on the display, it interrupts the pellet loading and increases the speed of the ue gas exhaust motor for a programmed

period of time. When the cleaning phase is nished, the stove will re-start automatically and continue the working phase, returning to the

selected power level.

SWITCHOFF

Press the key

for three seconds.

Once this operation has been performed, the appliance automatically enters the switch-o phase, blocking the supply of pellets.

The ue gas exhaust motor and the hot air ow motor will remain on until the stove temperature has dropped below the default

parameters.

REIGNITION

 The stove can be re-ignited only if the ue gas temperature has lowered, and if the pre-set timer has been reset.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Extraflame Mietta Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Extraflame Mietta

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info