Bedienungsanleitung Extraflame Mietta (Seite 27 von 40) (Englisch)

695849

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

ENGLISH

SETTINGS

DISPLAY

The "DISPLAY" menu allows:

 Regulation of Display contrast

 Activation/Deactivation of backlight.

 Enabling/disabling of acoustic signal.

 Set the timer to turn o the Display

backlight.

 Set the timer to turn o the Display (sleep

mode).

To set: OK > SETTINGS > DISPLAY.

STANDBY

The STAND-BY function is used if the stove needs to be turned o immediately or the modulation

via an additional thermostat is required. The display will feature the word STAND-BY which indicates

the active function.

To set: OK > SETTINGS > STANDBY.

STANDBY FUNCTION SET TO ON

When the STAND  BY. function is active (ON), if the room temperature exceeds the set value plus DELTA T OFF, the stove will switch o after

a pre-set (default) delay period, and STAND  BY will be displayed on the screen.

When the room temperature is lower than the set value less DELTA T ON and the stove has cooled, it will start to work again at the set power,

and work will be displayed on the screen.

STANDBY FUNCTION SET TO OFF FACTORY SETTING

When the STAND-BY function is not activated (OFF), if the stove reaches the set room temperature, it will switch to the minimum power level,

modulating and displaying modulation on the screen. When the room temperature is lower than the set value, the stove will start to work

again at the set power, and work will be displayed on the screen.

STANDBY WITH ADDITIONAL THERMOSTAT OPTIONAL

STANDBY FUNCTION SET TO OFF FACTORY SETTING

When the STAND-BY function is not activated (OFF), if the stove reaches the room temperature set on the supplementary thermostat (open

contact), it will switch to the minimum power level and display MODULATION on the screen. When the room temperature is lower than the

set value on the supplementary thermostat (closed contact), the stove will start to work again at the set power, and WORK will be displayed

on the screen.

STANDBY FUNCTION SET TO ON

If the STAND-BY function is activated (ON), when the room temperature set on the supplementary thermostat is reached (open contact), the

stove will switch o after a pre-set (default) delay period, and STAND - BY will be displayed on the screen.

When the room temperature is lower than the value set on the supplementary thermostat (closed contact), the stove will start to work again

at the set power, and WORK will be displayed on the screen

FOR CORRECT OPERATION, SET THE ROOM TEMPERATURE TO LOW-TA

 DATE/TIME

 LANGUAGE

 SET DEGREES

SEE CHAPTER: COMMISSIONING SETTINGS.

THIS FUNCTION IS NOT RECOMMENDED FOR ENVIRONMENTS WITH SCARCE THERMAL INSULATION OR WHERE

THERE MAY BE SHARP FLUCTUATIONS IN TEMPERATURE: DOORS OR WINDOWS CONSTANTLY OPENED.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Extraflame Mietta Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Extraflame Mietta

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info